Nissan Leaf. Instruction — part 689
PRECAUTIONS
FSU-5
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Indicate "HIGH VOLTAGE. DO NOT TOUCH" on the vehicle under repair/inspection to call attention to other
workers.
Precaution for Removing 12V Battery
INFOID:0000000010119422
1. Check that EVSE is not connected.
NOTE:
If EVSE is connected, the air conditioning system may be automatically activated by the timer A/C func-
tion.
2. Turn the power switch OFF
→ ON → OFF. Get out of the vehicle. Close all doors (including back door).
JSAIA1600GB
FSU-6
< PRECAUTION >
PRECAUTIONS
3. Check that the charge status indicator lamp does not blink and wait for 5 minutes or more.
NOTE:
If the battery is removed within 5 minutes after the power switch is turned OFF, plural DTCs may be
detected.
4. Remove 12V battery within 1 hour after turning the power switch OFF
→ ON → OFF.
NOTE:
• The 12V battery automatic charge control may start automatically even when the power switch is in
OFF state.
• Once the power switch is turned ON
→ OFF, the 12V battery automatic charge control does not start for
approximately 1 hour.
CAUTION:
• After all doors (including back door) are closed, if a door (including back door) is opened before
battery terminals are disconnected, start over from Step 1.
• After turning the power switch OFF, if “Remote A/C” is activated by user operation, stop the air
conditioner and start over from Step 1.
Precautions for Suspension
INFOID:0000000010119423
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fluids and lubricants are full. Tire repair kit and mats are in designated posi-
tions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
• The tightening surface must be kept free from oil/grease.
• When jacking up the vehicle with a floor jack, never hang the jack on the torque rod.
PREPARATION
FSU-7
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010119424
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000010119425
Tool number
(TechMate No.)
Tool name
Description
ST35652000
( — )
Strut attachment
Disassembling and assembling strut
ZZA0807D
Tool name
Description
Spring compressor
Removing and installing coil spring
Insulated gloves
[Guaranteed insulation performance for
1000V/300A]
Removing and installing high voltage com-
ponents
Leather gloves
[Use leather gloves that can fasten the wrist
tight]
• Removing and installing high voltage
components
• Protect insulated gloves
Insulated safety shoes
Removing and installing high voltage com-
ponents
S-NT717
JMCIA0149ZZ
JPCIA0066ZZ
JPCIA0011ZZ
FSU-8
< PREPARATION >
PREPARATION
Safety glasses
[ANSI Z87.1]
• Removing and installing high voltage
components
• To protect eye from the spatter on the
work to electric line
Face shield
• Removing and installing high voltage
components
• To protect face from the spatter on the
work to electric line
Insulated helmet
Removing and installing high voltage com-
ponents
Power tool
Loosening nuts, screws and bolts
Tool name
Description
JPCIA0012ZZ
JPCIA0167ZZ
JPCIA0013ZZ
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст