Nissan Frontier D40. Instruction — part 576
EM-36
< ON-VEHICLE REPAIR >
[QR25DE]
ROCKER COVER
ROCKER COVER
Exploded View
INFOID:0000000005274279
Removal and Installation
INFOID:0000000005274280
REMOVAL
1.
Remove intake manifold. Refer to
.
2.
Disconnect PCV hose from rocker cover.
3.
Remove ignition coils. Refer to
4.
Remove PCV valve and O-ring from rocker cover, if necessary.
5.
Remove oil filler cap from rocker cover, if necessary.
6.
Loosen bolts in reverse order as shown.
7.
Remove rocker cover gasket from rocker cover.
8.
Use scraper to remove all traces of liquid gasket from cylinder head and camshaft bracket (No. 1).
CAUTION:
Do not scratch or damage the mating surface when cleaning off old liquid gasket.
INSTALLATION
1.
PCV hose
2.
PCV valve
3.
O-ring
4.
Oil filler cap
5.
Rocker cover
6.
Rocker cover gasket
7.
PCV hose
WBIA0650E
PBIC3003E
ROCKER COVER
EM-37
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Apply liquid gasket using Tool to joint of rocker cover, cylinder
head and camshaft bracket (No. 1) as follows:
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
a.
Apply liquid gasket to joint part of camshaft bracket (a) (No. 1)
and cylinder head.
b.
Apply liquid gasket (b) 90
°
to figure (a).
2.
Install new rocker cover gasket to rocker cover.
3.
Install rocker cover.
• Check to be sure rocker cover gasket is not dropped from installation groove of rocker cover.
4.
Tighten bolts in two steps in numerical order as shown.
5.
Installation of the remaining components is in the reverse order of removal.
Tool number
: WS39930000 ( — )
PBIC2635E
1st step
: 2.0 N·m (0.2 kg-m, 18 in-lb)
2nd step
: 8.3 N·m (0.85 kg-m, 73 in-lb)
PBIC3003E
EM-38
< ON-VEHICLE REPAIR >
[QR25DE]
FUEL INJECTOR AND FUEL TUBE
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000005274281
Removal and Installation
INFOID:0000000005274282
CAUTION:
Do not remove or disassemble parts unless instructed as shown.
REMOVAL
WARNING:
• Put a “CAUTION FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
1.
Release fuel pressure. Refer to
.
2.
Disconnect the fuel quick connector on the engine side.
1.
Fuel feed hose
2.
Quick connector cap (engine side)
3.
Sub-harness
4.
Fuel tube
5.
O-ring (black)
6.
Clip
7.
Fuel injector
8.
O-ring (green)
WBIA0649E
LBIA0450E
FUEL INJECTOR AND FUEL TUBE
EM-39
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Remove quick connector cap.
b.
With the sleeve side of Tool facing quick connector, install Tool
onto fuel tube.
c.
Insert Tool into quick connector until sleeve contacts and goes
no further. Hold the Tool on that position.
CAUTION:
Inserting the Tool hard will not disconnect quick connector.
Hold Tool where it contacts and goes no further.
d.
Pull the quick connector straight out from the fuel tube.
CAUTION:
• Pull quick connector holding it at the (A) position, as shown.
• Do not pull with lateral force applied. O-ring inside quick connector may be damaged.
• Prepare container and cloth beforehand as fuel will leak out.
• Avoid fire and sparks.
• Do not expose parts to battery electrolyte or other acids.
• Do not bend or twist connection between quick connector and fuel feed hose during removal
and installation.
• Be sure to cover openings of disconnected pipes with
plug or plastic bag to avoid fuel leakage and entry of for-
eign materials.
3.
Remove intake manifold. Refer to
EM-27, "Removal and Installation"
4.
Disconnect harness connector from fuel injector.
5.
Loosen bolts in reverse order as shown and remove fuel tube
and fuel injector assembly.
CAUTION:
• Be careful to avoid any interference with fuel injector.
• Use a shop cloth to absorb any fuel leaks from fuel tube.
KBIA0701E
Tool number
:
—
(J-45488)
KBIA0702E
PBIC2205E
PBIC2998E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст