Nissan Frontier D40. Instruction — part 959
SE-36
< DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Fold Flat Passenger Seat
10. Seat cushion front finisher
11. Passenger seat wiring harness
12. Power seat frame assembly
13. Seat cushion inner finisher
14. Seat belt buckle assembly
15. Leg cover
16. Seat cushion rear finisher
17. Instruction seat frame assembly
18. Recline lever
19. Seat cushion rear finisher
20. Seatback board
21. Headrest holder with multi position
lock
22. Headrest holder
AWJIA0469GB
FRONT SEAT
SE-37
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Seatback Assembly
INFOID:0000000005274470
REMOVAL
NOTE:
On vehicles equipped with side air bags, only complete seatback assemblies can be replaced.
1.
Remove the front seat assembly. Refer to
SE-28, "Removal and Installation"
.
2.
Remove the seatback board from the back of the seatback.
3.
Remove the retainer.
4.
Disconnect the seatback heater harness.
5.
Remove the seatback bolts (2 for each side) and seatback assembly.
SEATBACK BOARD - SOFT SEATBACK
Removal
1.
Remove the seatback assembly. Refer to
SE-28, "Removal and Installation"
.
2.
The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 2 side tabs (B)
• 2 bottom clips (C) (must be replaced)
3.
Move seat to forward position.
1.
Front seatback lever
2.
Headrest
3.
Seatback assembly
4.
Seat cushion assembly
5.
Seat cushion outer finisher
6.
Leg cover
7.
Seat frame assembly
8.
Passenger seat wiring harness
9.
Seat cushion inner cover
10. Inboard reclining arm outer cover
11. Seat belt buckle assembly
12. Leg cover
13. Inboard reclining arm inner cover
14. Outboard reclining arm inner cover
15. Seat cushion rear finisher
16. Outboard reclining arm outer cover
17. Seatback board
18. Headrest holder with multi position
lock
19. Headrest holder
SIIA0113E
ALIIA0366ZZ
SE-38
< DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
4.
Hold the seatback board as shown and pull the top of the seat-
back board down and away from the seat back frame.
5.
Pull the middle part of the seatback board to disengage the side
tabs from the seatback frame.
6.
Pull the lower part of the seatback board to disengage the bot-
tom clips from the seatback frame.
Installation
Installation is in the reverse order of removal.
• The two bottom clips must be replaced for installation
• Secure the side tabs last for installation
SEATBACK BOARD - HARD SEATBACK
Removal
1.
Remove the seatback assembly. Refer to
SE-28, "Removal and Installation"
2.
The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 2 side tabs (B)
• 2 bottom clips (C) (must be replaced)
3.
Move seat to forward position.
4.
Hold the seatback board as shown and pull the bottom of the
seatback board away from the seat back frame.
ALIIA0368ZZ
ALIIA0367ZZ
ALIIA0369ZZ
ALIIA0370ZZ
FRONT SEAT
SE-39
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5.
Pull the middle part of the seatback board up and away to disen-
gage the side tabs from the seatback frame.
6.
Lift the upper part of the seatback board to disengage the top tabs from the seatback frame.
Installation
Installation is in the reverse order of removal.
• The two bottom clips must be replaced for installation
• Secure the side tabs last for installation
INSTALLATION
Installation is in the reverse order of removal.
Seat Cushion Trim and Pad
INFOID:0000000005274471
REMOVAL
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do
not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
1.
Remove the front seat assembly. Refer to
SE-28, "Removal and Installation"
.
2.
Remove the power seat switch knobs and power seat switch
escutcheon (if equipped) (or lift knobs on instruction seats).
ALIIA0371ZZ
LIIA0681E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст