Nissan Frontier D40. Instruction — part 52
BCS-18
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
MULTIREMOTE ENT
MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)
INFOID:0000000005275676
WORK SUPPORT
Hazard and horn reminder mode
DATA MONITOR
ACTIVE TEST
Work Item
Description
HORN CHIRP SET
Horn chirp function mode can be changed in this mode. The function mode will be changed when
"ON" or "OFF" on CONSULT-III screen is touched.
HAZARD LAMP SET
• MODE1: Nothing
• MODE2: Unlock only
• MODE3: Lock only
• MODE4: Lock and unlock
MULTI ANSWER BACK SET
Hazard and horn reminder mode can be changed in this mode. See table below for details.
AUTO LOCK SET
• MODE1: 5 minutes
• MODE2: Nothing
• MODE3: 1 minute
PANIC ALARM SET
• MODE1: 0.5 seconds
• MODE2: Nothing
• MODE3: 1.5 seconds
PW DOWN SET
• MODE1: 2 seconds
• MODE2: Nothing
• MODE3: 5 seconds
REMO CONT ID REGIST
Keyfob ID code can be registered.
REMO CONT ID ERASUR
Keyfob ID code can be erased.
REMO CONT ID CONFIR
It can be checked whether keyfob ID code is registered or not in this mode.
MODE 1
(C mode)
MODE 2
(S mode)
Keyfob
operation
Lock
Unlock
Lock
Unlock
Hazard warning lamp flash
Twice
Once
Twice
—
Horn sound
Once
—
—
—
Monitor Item
[Unit}
Condition
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position
KEY ON SW [ON/OFF]
Indicates condition of key switch
ACC ON SW [ON/OFF]
Indicates condition of ignition switch in ACC position
KEYLESS LOCK [ON/OFF]
Indicates condition of lock signal from keyfob
KEYLESS UNLOCK [ON/OFF]
Indicates condition of unlock signal from keyfob
KEYLESS PANIC [ON/OFF]
Indicates condition of panic signal from keyfob
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch (all) and rear door switch upper and lower (king cab) LH
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch (all) and rear door switch upper and lower (king cab) RH
DOOR SW-RR [ON/OFF]
Indicates condition of rear door switch RH (crew cab)
DOOR SW-RL [ON/OFF]
Indicates condition of rear door switch LH (crew cab)
CDL LOCK SW [ON/OFF]
Indicates condition of door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Indicates condition of door lock and unlock switch
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-19
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000005275677
WORK SUPPORT
*: Initial setting
DATA MONITOR
ACTIVE TEST
Test Item
Description
DOOR LOCK
This test is able to check door lock operation. The doors lock and unlock based on the item on CON-
SULT-III screen touched.
PW REMOTO DOWN SET
This test is able to check power window down operation. The windows are lowered when “ON” on
CONSULT-III screen is touched.
FLASHER
This test is able to check right and left hazard reminder operation. The right hazard lamp turns on
when “RH” on CONSULT-III screen is touched and the left hazard lamp turns on when "LH" on CON-
SULT-III screen is touched.
HORN
This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
Work Item
Setting item
Setting
BATTERY SAVER SET
ON*
With the exterior lamp battery saver function
OFF
Without the exterior lamp battery saver function
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW [ON/OFF]
Ignition switch (ACC) status judged from ACC signal (accessory power supply)
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1 [ON/OFF]
HEAD LAMP SW 2 [ON/OFF]
LIGHT SW 1ST [ON/OFF]
AUTO LIGHT SW [ON/OFF]
PASSING SW [ON/OFF]
FR FOG SW [ON/OFF]
TURN SIGNAL R [ON/OFF]
TURN SIGNAL L [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch LH
DOOR SW-AS [ON/OFF]
The switch status input from front door switch RH
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW-RL [ON/OFF]
The switch status input from rear door switch LH
CARGO LAMP SW [ON/OFF]
Cargo lamp status that BCM judges from the vehicle condition
OPTICAL SENSOR [ON/OFF]
The value of exterior brightness voltage input from the optical sensor
Test Item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
BCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000005275678
WORK SUPPORT
*: Factory setting
DATA MONITOR
ACTIVE TEST
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
CARGO LAMP
ON
Transmits the cargo lamp request signal to IPDM E/R with CAN commu-
nication to turn the each lamp ON.
OFF
Stops the cargo lamp request signal transmission.
Test Item
Operation
Description
Work Item
Setting
Item
Description
WIPER SPEED
SETTING
ON
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch ON status judged from ignition power supply
IGN SW CAN [ON/OFF]
Ignition switch ON status received from IPDM E/R with CAN communication
FR WIPER HI [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
FR WIPER LOW [ON/OFF]
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7]
Each switch status that BCM judges from the combination switch reading function
FR WIPER STOP [ON/OFF]
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion
VEHICLE SPEED [km/h]
The value of the vehicle speed signal received from combination meter with CAN com-
munication
Test Item
Operation
Description
FR WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000005275679
DATA MONITOR
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER)
INFOID:0000000005275680
DATA MONITOR
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
INFOID:0000000005275681
DATA MONITOR
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF]
The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
BRAKE SW [ON/OFF]
The switch status input from the brake switch
Test Item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
OFF
Stops the voltage to turn the turn signal lamps OFF.
Monitor Item
[Unit]
Contents
IGN ON SW [ON/OFF]
Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged from ignition
switch signal
FAN ON SIG [ON/OFF]
Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal
AIR COND SW [ON/OFF]
Display [COMP (On)/COMP (Off)] status as judged from air conditioner switch signal
Monitor Item
[Unit]
Description
TURN SIGNAL R
[OFF/ON]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function
TURN SIGNAL L
[OFF/ON]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function
HI BEAM SW
[OFF/ON]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function
HEAD LAMP SW 1
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
HEAD LAMP SW 2
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
LIGHT SW 1ST
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст