Nissan Frontier D40. Instruction — part 853
MWI
METER SYSTEM
MWI-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SHIFT POSITION INDICATOR : Component Description
INFOID:0000000005275802
WARNING LAMPS/INDICATOR LAMPS
WARNING LAMPS/INDICATOR LAMPS : System Diagram
INFOID:0000000005275803
WARNING LAMPS/INDICATOR LAMPS : System Description
INFOID:0000000005275804
OIL PRESSURE WARNING LAMP
• IPDM E/R reads the ON/OFF signals from the oil pressure switch and transmits the oil pressure switch sig-
nal to the combination meter via BCM with the CAN communication line.
• The combination meter turns the oil pressure warning lamp ON/OFF according to the oil pressure switch sig-
nal received via CAN communication.
WARNING LAMPS/INDICATOR LAMPS : Component Parts Location
INFOID:0000000005548839
Unit
Description
Combination meter
Displays the shift position using shift position signal received from TCM.
TCM
Transmits the shift position signal to the combination meter via CAN communication.
JSNIA0449GB
AWNIA0781ZZ
MWI-18
< FUNCTION DIAGNOSIS >
METER SYSTEM
WARNING LAMPS/INDICATOR LAMPS : Component Description
INFOID:0000000005275806
TRIP COMPUTER
TRIP COMPUTER : System Diagram
INFOID:0000000005275807
TRIP COMPUTER : System Description
INFOID:0000000005275808
FUNCTION
The trip computer can indicate the following items.
• DTE (distance to empty)
• Trip distance
• Trip time
• Average fuel consumption
• Average vehicle speed
DTE (DISTANCE TO EMPTY) INDICATION
The range indication provides the driver with an estimation of the distance that can be driven before refueling.
The range is calculated by signals from the fuel level sensor unit (fuel remaining), ECM (fuel consumption)
and the ABS actuator and electric unit (vehicle speed). The indication will be refreshed every 30 seconds.
When fuel remaining is less than approximately 11.6 (3 1/8 US gal, 2 1/2 Imp gal), the indication will blink as
a warning. If the fuel remaining is less than approximately 9.6 (2 1/2 US gal, 2 1/8 Imp gal), the indication will
show “---”. In this case, the display will change to the DTE mode even though the display is showing a different
1.
Combination meter M24
2.
Fuel level sensor unit and fuel pump C5
(view with fuel tank removed)
3.
ECM (view with ECM cover removed)
E8 (with VQ40DE)
E16 (with QR25DE)
A. Coolant reservoir
4.
ABS actuator and electric unit (control
unit) E127
5.
Oil pressure switch E208 (with VQ40DE)
A. Oil pan (upper)
6.
Oil pressure switch F4 (with
QR25DE) (view with engine re-
moved)
7.
A/T assembly F9
8.
BCM M18, M19 (view with lower instru-
ment panel LH removed)
Unit
Description
Combination meter
Turns the oil pressure warning lamp ON/OFF according to the oil pressure switch signal received
from BCM by means of communication.
IPDM E/R
Reads the ON/OFF signals from the oil pressure switch and transmits the oil pressure switch signal
to the combination meter via BCM with the CAN communication line.
Oil pressure switch
Refer to
.
BCM
Transmits the oil pressure switch signal received from IPDM E/R via CAN communication to the
combination meter via CAN communication.
AWNIA0218GB
MWI
METER SYSTEM
MWI-19
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
mode. When the battery is disconnected and reconnected, DTE mode will display “---” until the vehicle is
driven 0.3 miles (0.5 km).
TRIP DISTANCE
Trip distance is calculated by signal from the ABS actuator and electric unit (vehicle speed). If trip distance is
reset, trip time will be reset at the same time.
TRIP TIME
Trip time displays cumulative ignition switch ON time. If trip time is reset, trip distance will be reset at the same
time.
AVERAGE FUEL CONSUMPTION
Average fuel consumption indication is calculated by signals from the ABS actuator and electric unit (vehicle
speed) and the ECM (fuel consumption). The indication will be refreshed every 30 seconds.
AVERAGE VEHICLE SPEED
Average vehicle speed indication is calculated by running distance and running time. The indication will be
refreshed every 30 seconds. If average vehicle speed is reset, average fuel consumption will be reset at the
same time. After resetting, the display will show “---” for 30 seconds.
HOW TO CHANGE/RESET INDICATION
Refer to Owner's Instruction for trip computer operating instructions.
TRIP COMPUTER : Component Parts Location
INFOID:0000000005548840
AWNIA0781ZZ
1.
Combination meter M24
2.
Fuel level sensor unit and fuel pump C5
(view with fuel tank removed)
3.
ECM (view with ECM cover removed)
E8 (with VQ40DE)
E16 (with QR25DE)
A. Coolant reservoir
4.
ABS actuator and electric unit (control
unit) E127
5.
Oil pressure switch E208 (with VQ40DE)
A. Oil pan (upper)
6.
Oil pressure switch F4 (with
QR25DE) (view with engine re-
moved)
7.
A/T assembly F9
8.
BCM M18, M19 (view with lower instru-
ment panel LH removed)
MWI-20
< FUNCTION DIAGNOSIS >
METER SYSTEM
TRIP COMPUTER : Component Description
INFOID:0000000005275810
Unit
Description
Combination meter
Controls the information display according to the signal received from each unit.
Fuel level sensor unit
Refer to
.
ECM
Transmits the following signals to the combination meter via CAN communication line.
• Engine speed signal
• Fuel consumption monitor signal
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter via CAN communication line.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст