Nissan Frontier D40. Instruction — part 192
SERVICE DATA AND SPECIFICATIONS (SDS)
CO-29
< SERVICE DATA AND SPECIFICATIONS (SDS)
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit
INFOID:0000000005276100
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, Imp qt)
RADIATOR
Unit: kPa (kg/cm
2
, psi)
THERMOSTAT
WATER CONTROL VALVE
Engine coolant capacity (With reservoir tank at “MAX” level)
9.4 (10, 8-1/4)
Cap relief pressure
Standard
98 - 118 (1.0 - 1.2, 14- 17)
Leakage test pressure
137 (1.4, 20)
Valve opening temperature
80.5 - 83.5
°
C (177 - 182
°
F)
Full-open lift amount
8 mm/ 95
°
C (0.315 in/ 203
°
F)
Valve closing temperature
77
°
C (171
°
F)
Valve opening temperature
93.5 - 96.5
°
C (200 - 206
°
F)
Full-open lift amount
More than 8 mm/ 108
°
C (0.315 in/ 226
°
F)
Valve closing temperature
90
°
C (194
°
F) or higher
CO-30
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005575333
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Liquid Gasket
INFOID:0000000005276102
REMOVAL OF LIQUID GASKET SEALING
• After removing nuts and bolts, separate the mating surface, using Tool and remove old liquid gasket sealing.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap (1) Tool to insert it, and then slide (2) it by tapping on the side
as shown.
• In areas where Tool is difficult to use, use plastic hammer to lightly
tap the parts, to remove it.
CAUTION:
If for some unavoidable reason suitable tool such as screw-
driver is used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
Tool number
: KV10111100 (J-37228)
WBIA0566E
PRECAUTIONS
CO-31
< PRECAUTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
1.
Remove the old liquid gasket adhering to the gasket application
surface and the mating surface using suitable tool.
• Remove the liquid gasket completely from the groove of the
liquid gasket application surface, bolts, and bolt holes.
2.
Thoroughly clean the mating surfaces and remove adhering
moisture, grease and foreign material.
3.
Attach the liquid gasket tube to the Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• As for the bolt holes, normally apply the liquid gasket inside
the holes. If specified in the procedure, it should also be
applied outside the holes.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• Wait 30 minutes or more after installation before refilling the
engine with engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
PBIC0003E
Tool number
: WS39930000 (
—
)
WBIA0567E
SEM159F
CO-32
< PREPARATION >
[VQ40DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005276103
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005276104
Tool number
(Kent-Moore No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing chain tensioner cover and water
pump cover
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
EG17650301
(J-33984-A)
Radiator cap tester adapter
Adapting radiator cap tester to radiator cap
and radiator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
KV991J0070
(J-45695)
Coolant refill tool
Filling cooling system
KV991J0010
(J-23688)
Engine coolant refractometer
Checking concentration of ethylene glycol in
engine coolant
NT046
S-NT052
S-NT564
LMA053
WBIA0539E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст