Nissan Frontier D40. Instruction — part 924
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-5
< SERVICE INFORMATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005274995
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
ta
lla
tio
n
,
lo
os
en
es
s
P
a
rt
s interference
W
he
el be
arin
g da
ma
ge
PR
OP
EL
LE
R
S
H
A
F
T
REA
R
FINAL DRIVE
S
U
S
PENSION
TI
RE
S
ROAD W
H
EEL
BR
AK
E
S
Symptom
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
×
RAX-6
< SERVICE INFORMATION >
[C200]
ON-VEHICLE SERVICE
ON-VEHICLE SERVICE
Rear Axle Parts
INFOID:0000000005274996
• Check the axle parts for excessive play, wear and damage. Replace as necessary.
• Shake each rear wheel to check for excessive play. Repair as nec-
essary.
• Retighten all nuts and bolts to the specified torque. Refer to
Rear Axle Bearing
INFOID:0000000005274997
• Check that the axle shaft bearing operates smoothly. Replace as necessary.
• Check axial end play. Refer to
SMA525A
AXLE SHAFT
RAX-7
< SERVICE INFORMATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
AXLE SHAFT
Removal and Installation
INFOID:0000000005274998
CAUTION:
Before removing the rear axle, disconnect the ABS wheel sensor from the assembly. Then move it
away from the axle. Failure to do so may result in damage to the sensor wires and the sensor becom-
ing inoperative.
• Wheel bearing does not require maintenance.
• If growling noise is emitted from wheel bearing during operation, replace wheel bearing assembly.
• If the wheel bearing assembly is removed, it must be replaced. The old assembly must not be re-used.
1.
Axle shaft
2.
Grease catcher
3.
Wheel stud
4.
Axle bearing stud
5.
Back plate and torque member
6.
Axle bearing
7.
Bearing ring retainer
8.
Shim washer
9.
Snap ring
10. ABS sensor rotor
11.
O-ring
12. Axle oil seal
13. Breather
14. Rear final drive
WDIA0280E
RAX-8
< SERVICE INFORMATION >
[C200]
AXLE SHAFT
REMOVAL
1.
Remove the ABS wheel sensor from the axle case and reposition out of the way. Refer to
(Type 1),
BRC-178, "Removal and Installation"
(Type 2)
(Type 3).
2.
Remove the rear brake caliper assembly without disconnecting the brake hose and reposition out of the
way. Refer to
BR-46, "Removal and Installation of Brake Caliper and Disc Rotor"
3.
Remove the parking brake assembly from the back plate and torque member. Refer to
4.
Remove the axle bearing nuts securing the axle shaft assembly to the axle case.
5.
Draw the axle shaft assembly out of the axle case using suitable tool.
6.
Remove the O-ring.
7.
Remove the axle oil seal using Tools as shown.
• Do not reuse the axle oil seal once it is removed. Always
install a new axle oil seal.
• Apply a constant pressure on the slide hammer while turning
the slide hammer 180
°
degrees periodically while pulling the
axle oil seal out.
8.
Remove the ABS sensor rotor using Tool. Discard the ABS sen-
sor rotor.
NOTE:
Always replace the ABS sensor rotor with a new one.
9.
Remove the snap ring and shim washer. Discard the snap ring and shim washer.
NOTE:
Always replace the snap ring and shim washer with new ones.
10. Remove the bearing ring retainer from the axle shaft using Tool
as shown. Discard the bearing ring retainer.
NOTE:
Always replace the bearing ring retainer with a new one.
11. Remove the back plate and torque member with the axle bearing attached from the axle shaft using a suit-
able press.
12. Remove the axle bearing studs to release the axle bearing from the back plate and torque member using
a suitable hammer or press.
13. Remove the wheel studs using a suitable hammer or press.
14. Remove the grease catcher from the axle shaft.
Tool number
A:
—
(J-26941 part of J-46215)
B: —
(J-23907)
LDIA0030E
Tool number
: KV40106500 (J-45073)
LDIA0031E
Tool number
: KV40106500 (J-45073)
LDIA0031E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст