Nissan Frontier D40. Instruction — part 796
INT-16
< ON-VEHICLE REPAIR >
DOOR FINISHER
REAR DOOR - KING CAB
Removal
1.
Remove lower seat belt anchor bolt. Refer to
SB-15, "Removal and Installation"
.
• Disconnect harness connector for passenger side.
2.
Release the clips and remove rear door finisher.
3.
Remove lock lever assembly.
• Disconnect lock lever cable and lever assembly. Refer to
DLK-139, "Removal and Installation"
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Latch cover
3.
Guide
4.
Rear door finisher
5.
Metal clip
LIIA1963E
BODY SIDE TRIM
INT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Component
INFOID:0000000005274449
CREW CAB
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (RH side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Front door welt
10. Front pillar lower finisher
11.
Front pillar upper finisher
12.
Front pillar assist grip
13. LH side demister grille
14.
Molded plastic clip
15.
Finisher
C.
Clip C101
D.
Clip C111
E.
Metal clip
Front
AWJIA0051GB
INT-18
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
KING CAB
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
Removal and Installation
INFOID:0000000005274450
LOWER DASH SIDE FINISHER
Removal
1.
Remove push pin from lower dash side finisher.
2.
Remove front kick plate from center pillar lower finisher.
1.
Door welt
2.
Rear kick plate
3.
Front kick plate
4.
Lower dash side finisher
5.
Front pillar lower finisher
6.
Side demister grille
7.
Front pillar assist grip
8.
Front pillar upper finisher
9.
Molded plastic clip
10. Metal clip
11.
Garnish
LIIA1962E
BODY SIDE TRIM
INT-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Remove front kick plate from dash side from lower dash side finisher.
4.
Remove lower dash side finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal
1.
Remove front and rear door welts.
2.
Remove seat belt anchor. Refer to
SB-15, "Removal and Installation"
• On RH side, remove the cover and disconnect seat belt tension sensor.
3.
Remove front and rear kick plates.
4.
Remove center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1.
Remove front and rear door welts.
2.
Remove seat belt shoulder anchor and D-ring. Refer to
SB-15, "Removal and Installation"
3.
Remove front and rear kick plates.
4.
Remove center pillar lower finisher.
5.
Remove assist grip.
6.
Remove center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR UPPER FINISHER
Removal
1.
Remove front pillar lower finisher.
2.
Remove the front pillar assist grip.
3.
Remove the front pillar upper finisher bolt.
4.
Remove the front pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR LOWER FINISHER
Removal
1.
Remove front door welt and kick plate.
2.
Remove the front pillar lower finisher.
Installation
Installation is in the reverse order of removal.
KICK PLATES
Removal
Release clips and remove front and/or rear kick plates.
Installation
Installation is in the reverse order of removal.
REAR TRIM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст