Nissan Frontier D40. Instruction — part 826
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit
INFOID:0000000005272522
OIL PRESSURE
Unit: kPa (kg/cm
2
, psi)
*: Engine oil temperature at 80
°
(176
°
F)
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, Imp qt)
Engine speed
Approximate discharge oil pressure*
Idle speed
More than 98 (1.0, 14)
2,000 rpm
More than 294 (3.0, 43)
Drain and refill
With oil filter change
4.6 (4-7/8, 4)
Without oil filter change
4.3 (4-1/2, 3-3/4)
Dry engine (Overhaul)
5.0 (5-1/4, 4-3/8)
LU-16
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005575331
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Liquid Gasket
INFOID:0000000005272524
REMOVAL OF LIQUID GASKET SEALING
• After removing the bolts and nuts, separate the mating surface and
remove the old liquid gasket sealing using Tool.
CAUTION:
Do not damage the mating surfaces.
• Tap (1) the Tool to insert it.
• In areas where the Tool is difficult to use, lightly tap to slide (2) it.
LIQUID GASKET APPLICATION PROCEDURE
Tool number
: KV10111100 (J-37228)
WBIA0566E
PRECAUTIONS
LU-17
< PRECAUTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
1.
Remove the old liquid gasket adhering to the gasket application
surface and the mating surface using suitable tool.
• Remove the liquid gasket completely from the groove of the
liquid gasket application surface, bolts, and bolt holes.
2.
Thoroughly clean the mating surfaces and remove adhering
moisture, grease and foreign material.
3.
Attach the liquid gasket tube to the Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• As for the bolt holes, normally apply the liquid gasket inside
the holes. If specified in the procedure, it should also be
applied outside the holes.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• Wait 30 minutes or more after installation before refilling the
engine with engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
PBIC0003E
Tool number
: WS39930000 (
—
)
WBIA0567E
SEM159F
LU-18
< PREPARATION >
[VQ40DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005272525
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005272526
Tool number
(Kent-Moore No.)
Tool name
Description
ST25051001
(J-25695-1)
Oil pressure gauge
Measuring oil pressure
Maximum measuring range:
2,452 kPa (25 kg/cm
2
, 356 psi)
ST25052000
(J-25695-2)
Hose
Adapting oil pressure gauge to cylinder block
KV10111100
(J-37228)
Seal cutter
Removing steel oil pan and rear timing chain
case
KV10115801
(J-38956)
Oil filter wrench
Removing and installing oil filter
a: 64.3 mm (2.531 in)
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
S-NT050
S-NT559
NT046
S-NT375
S-NT052
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст