Nissan Frontier D40. Instruction — part 286
REAR PROPELLER SHAFT
DLN-165
< DISASSEMBLY AND ASSEMBLY >
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DISASSEMBLY AND ASSEMBLY
REAR PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000005840685
DISASSEMBLY
Journal
1.
Remove the propeller shaft assembly from the vehicle. Refer to
DLN-163, "Removal and Installation"
.
2.
Put matching marks on the rear propeller shaft tube and flange
yoke as shown.
CAUTION:
For matching marks use paint. Never damage the rear pro-
peller shaft or flange yoke.
3.
Remove the snap rings.
4.
Push out and remove the journal bearing by lightly tapping the
yoke with a hammer, taking care not to damage the journal or
yoke hole.
5.
Remove the bearing at the opposite side of above operation.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
SPD128
APD011
SPD732
SPD131
DLN-166
< DISASSEMBLY AND ASSEMBLY >
[3S1330]
REAR PROPELLER SHAFT
Center Support Bearing
1.
Remove the propeller shaft assembly from the vehicle. Refer to
DLN-163, "Removal and Installation"
2.
Put matching marks on the propeller shaft tube and the slip yoke.
CAUTION:
For matching marks, use paint. Never damage the propeller shaft tube or slip yoke.
3.
Remove and discard the clamp near the center support bearing, then slide the slip yoke off of propeller
shaft tube.
4.
Press the center support bearing off the propeller shaft tube
using Tool and suitable hydraulic press.
ASSEMBLY
Journal
1.
Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2.
Select snap rings that will provide the specified play in an axial
direction of the journal, and install them. Refer to
.
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3.
Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
Tool number
: 205-D002
LDIA0152E
WPD019
APD012
SPD732
REAR PROPELLER SHAFT
DLN-167
< DISASSEMBLY AND ASSEMBLY >
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
Center Support Bearing
1.
Apply a thin coat of multi-purpose grease to both the propeller shaft tube and the inside surface of the
center support bearing.
2.
Install the center support bearing on the propeller shaft tube
using a suitable pipe pressing on the inner race.
3.
Install a new clamp over the boot on the slip yoke.
4.
Align the matching marks and install the slip yoke on the propeller shaft tube.
5.
Clean the surfaces and position the boot over the propeller shaft tube and tighten the clamp.
6.
Install the center support bearing bracket, then install the rear
propeller shaft assembly in the vehicle. Refer to
LDIA0119E
LDIA0153E
WDIA0066E
DLN-168
< SERVICE DATA AND SPECIFICATIONS (SDS)
[3S1330]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000005275523
Snap Ring
INFOID:0000000005275524
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Applied model
VQ40DE
2WD
M/T short bed
M/T long bed
A/T long bed
Propeller shaft model
3S1330
Number of joints
3
Coupling method with
rear final drive
Flange type
Coupling method with
transmission
Sleeve type
1st Shaft length (Center
bearing to spider)
674.5
±
1.5 mm (26.56
±
0.06 in)
674.5
±
1.5 mm (26.56
±
0.06 in)
741.5
±
1.5 mm (29.19
±
0.06 in)
2nd Shaft length (Spider
to spider)
783.8
±
1.5 mm (30.86
±
0.06 in)
1138.8
±
1.5 mm (44.83
±
0.06 in )
1152.8
±
1.5 mm (45.39
±
0.06 in)
Shaft outer diameter
76.2 + 0.00/ - 0.13mm (3.00 + 0.00/ - 0.01 in)
Journal axial play
0.02 mm (0.0008 in) or less
Propeller shaft runout limit
0.6 mm (0.024 in) or less
Propeller shaft joint flex
effort
2.26 N·m (0.23 kg-m, 20 in-lb) or less
Thickness
Color
Part Number*
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
2.14 (0.0843)
Light brown
37151-C9400
2.17 (0.0854)
Black
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст