Nissan Frontier D40. Instruction — part 525
P1554 BATTERY CURRENT SENSOR
EC-791
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Install jumper cable between battery negative terminal and body
ground.
4.
Turn ignition switch ON.
5.
Check voltage between ECM terminal 71 (battery current sensor
signal) and ground.
6.
If NG, replace battery negative cable assembly.
BBIA0588E
Voltage: Approximately 2.5V
PBIB2617E
EC-792
< COMPONENT DIAGNOSIS >
[VQ40DE]
P1564 ASCD STEERING SWITCH
P1564 ASCD STEERING SWITCH
Component Description
INFOID:0000000005273797
ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation
of switch, and determines which button is operated.
On Board Diagnosis Logic
INFOID:0000000005273798
This self-diagnosis has the one trip detection logic.
The MIL will not illuminate for this diagnosis.
NOTE:
If DTC P1564 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to
.
DTC Confirmation Procedure
INFOID:0000000005273799
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
WITH CONSULT-III
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.
3.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
4.
Press RESUME/ACCELERATE switch for at least 10 seconds, then release it and wait at least 10 sec-
onds.
5.
Press SET/COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
6.
Check DTC.
7.
If DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000005273800
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
PBIB2645E
DTC No.
Trouble Diagnosis
Name
DTC Detecting Condition
Possible Cause
P1564
1564
ASCD steering switch
• An excessively high voltage signal from the ASCD
steering switch is sent to ECM.
• ECM detects that input signal from the ASCD steer-
ing switch is out of the specified range.
• ECM detects that the ASCD steering switch is stuck
ON.
• Harness or connectors
(The switch circuit is open or shorted.)
• ASCD steering switch
• ECM
P1564 ASCD STEERING SWITCH
EC-793
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK ASCD STEERING SWITCH CIRCUIT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “MAIN SW”, “CANCEL SW”, “RESUME/ACC SW” and “SET SW” in “DATA MONITOR” mode with
CONSULT-III.
3.
Check each item indication under the following conditions.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check voltage between ECM terminal 99 and ground with press-
ing each button.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 3.
3.
CHECK ASCD STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect combination switch harness connector.
BBIA0539E
Switch Monitor
item
Condition
Indication
MAIN switch
MAIN SW
Pressed
ON
Released
OFF
CANCEL switch
CANCEL SW
Pressed
ON
Released
OFF
RESUME/ACCELER-
ATE switch
RESUME/ACC SW
Pressed
ON
Released
OFF
SET/COAST switch
SET SW
Pressed
ON
Released
OFF
Switch
Condition
Voltage [V]
MAIN switch
Pressed
Approx. 0
Released
Approx. 4
CANCEL switch
Pressed
Approx. 1
Released
Approx. 4
RESUME/ACCELERATE
switch
Pressed
Approx. 3
Released
Approx. 4
SET/COAST switch
Pressed
Approx. 2
Released
Approx. 4
PBIB0311E
EC-794
< COMPONENT DIAGNOSIS >
[VQ40DE]
P1564 ASCD STEERING SWITCH
3.
Disconnect ECM harness connector.
4.
Check harness continuity between combination switch terminal 15 and ECM terminal 67. Refer to Wiring
Diagram.
5.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors M31, E152
• Harness connectors E5, F14
• Combination switch (spiral cable)
• Harness for open and short between ECM and combination switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 99 and combination switch terminal 14.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors M31, E152
• Combination switch (spiral cable)
• Harness for open and short between ECM and combination switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK ASCD STEERING SWITCH
EC-794, "Component Inspection"
OK or NG
OK
>> GO TO 8.
NG
>> Replace steering switch.
8.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000005273801
ASCD STEERING SWITCH
1.
Disconnect combination switch (spiral cable).
Continuity should exist.
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст