Nissan Frontier D40. Instruction — part 95
BRC-78
< BASIC INSPECTION >
[TYPE 2]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000005548209
After replacing the ABS actuator and electric unit (control unit), perform the following procedures:
• Neutral position adjustment for the steering angle sensor
• Calibration of the decel G sensor
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000005548210
1.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
Perform the neutral position adjustment for the steering angle sensor.
>> Refer to
BRC-78, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Spe-
, GO TO 2
2.
PERFORM CALIBRATION OF THE DECEL G SENSOR
Perform calibration of the decel G sensor.
>> Refer to
BRC-79, "CALIBRATION OF DECEL G SENSOR : Special Repair Requirement"
.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description
INFOID:0000000005548211
Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.
×
: Required –: Not required
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Re-
pair Requirement
INFOID:0000000005548212
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
CAUTION:
To adjust neutral position of steering angle sensor, make sure to use CONSULT-III
(Adjustment cannot be done without CONSULT-III)
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
Situation
Adjustment of steering angle sensor neutral position
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
Battery disconnection
×
INSPECTION AND ADJUSTMENT
BRC-79
< BASIC INSPECTION >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
>> GO TO 2
2.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1.
On the CONSULT-III screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2.
Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3.
After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4.
Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.
CHECK DATA MONITOR
1.
Run vehicle with front wheels in straight-ahead position, then stop.
2.
Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0
±
2.5
°
.
Is the steering angle within the specified range?
YES
>> GO TO 4
NO
>> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
BRC-95, "CONSULT-III Function (ABS)"
.
• ECM: Refer to
EC-528, "CONSULT-III Function (ENGINE)"
Are the memories erased?
YES
>> Inspection End
NO
>> Check the items indicated by the self-diagnosis.
CALIBRATION OF DECEL G SENSOR
CALIBRATION OF DECEL G SENSOR : Description
INFOID:0000000005548213
Refer to the table below to determine if calibration of the decel G sensor is required.
×
: Required –: Not required
CALIBRATION OF DECEL G SENSOR : Special Repair Requirement
INFOID:0000000005548214
CALIBRATION OF DECEL G SENSOR
CAUTION:
To calibrate the decel G sensor, make sure to use CONSULT-III
Situation
Calibration of decel G sensor
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
BRC-80
< BASIC INSPECTION >
[TYPE 2]
INSPECTION AND ADJUSTMENT
(Calibration cannot be done without CONSULT-III)
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2
2.
PERFORM CALIBRATION OF DECEL G SENSOR
1.
On the CONSULT-III screen, touch “WORK SUPPORT” and “DECEL G SEN CALIBRATION” in order.
2.
Touch “START”.
3.
After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4.
Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.
CHECK DATA MONITOR
1.
Run vehicle with front wheels in straight-ahead position, then stop.
2.
Select “DATA MONITOR”. Then make sure “DECEL G SEN” is within
±
0.08G.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Perform calibration of decel G sensor again, GO TO 1
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
BRC-95, "CONSULT-III Function (ABS)"
.
• ECM: Refer to
EC-528, "CONSULT-III Function (ENGINE)"
Are the memories erased?
YES
>> Inspection End
NO
>> Check the items indicated by the self-diagnosis.
APPLICATION NOTICE
BRC-81
< FUNCTION DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
FUNCTION DIAGNOSIS
APPLICATION NOTICE
Application Notice
INFOID:0000000005548387
Service information
Remarks
TYPE 1
ABS
TYPE 2
VDC/TCS/ABS
TYPE 3
HILL DESCENT CONTROL/HILL START ASSIST/VDC/TCS/ABS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст