Nissan Frontier D40. Instruction — part 605
EM-152
< ON-VEHICLE REPAIR >
[VQ40DE]
OIL PAN AND OIL STRAINER
17. Remove oil pan (upper) bolts with power tool in reverse order as
shown.
• Insert Tool between oil pan (upper) and lower cylinder block.
Tap (1) Tool to insert it and then slide (2) it by tapping on the
side as shown.
CAUTION:
Be careful not to damage mating surfaces.
18. Remove O-rings from bottom of lower cylinder block and oil
pump.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION (UPPER)
1.
Install oil pan (upper) as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of lower
cylinder block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
PBIC2887E
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC2885E
PBIC2884E
OIL PAN AND OIL STRAINER
EM-153
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
b.
Install new O-rings on the bottom of lower cylinder block and oil
pump.
c.
Apply a continuous bead of liquid gasket using Tool to the lower
cylinder block mating surfaces of oil pan (upper) as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
CAUTION:
• For bolt holes with mark, apply liquid gasket outside
the hole.
• Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-
ter to area (A).
• Attaching should be done within 5 minutes after coating.
d.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both oil pan gaskets and O-rings.
• Tighten oil pan (upper) bolts in numerical order as shown.
• There are two types of bolts.
e.
Tighten transmission joint bolts. Refer to
TM-69, "Removal and Installation from Vehicle (For 2WD Mod-
TM-71, "Removal and Installation from Vehicle (For 4WD Models)"
(4WD M/T
models),
TM-301, "Removal and Installation for VQ40DE 2WD Models"
"Removal and Installation for VQ40DE 4WD Models"
(4WD A/T models).
2.
Install oil strainer to oil pan (upper).
3.
Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and adjust as needed. Refer to
.
2.
Start engine, and check for leaks of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check engine oil level again. Refer to
PBIC2885E
Tool number
: WS39930000 (
—
)
PBIC2886E
M8
×
100 mm (3.97 in)
: 7, 11, 12, 13
M8
×
25 mm (0.98 in)
: Except the above
PBIC2887E
EM-154
< ON-VEHICLE REPAIR >
[VQ40DE]
IGNITION COIL
IGNITION COIL
Exploded View
INFOID:0000000005274336
Removal and Installation
INFOID:0000000005274337
REMOVAL (LH)
1.
Remove engine room cover. Refer to
EM-138, "Removal and Installation"
2.
Move aside harness, harness bracket, and hoses located above ignition coil.
3.
Disconnect the harness connector from ignition coil.
4.
Remove the ignition coil.
CAUTION:
Do not shock ignition coil.
INSTALLATION (LH)
Installation is in the reverse order of removal.
REMOVAL (RH)
1.
Remove intake manifold collector. Refer to
EM-140, "Removal and Installation"
2.
Move aside harness, harness bracket, and hoses located above ignition coil.
3.
Disconnect the harness connector from ignition coil.
4.
Remove the ignition coil.
CAUTION:
Do not shock ignition coil.
INSTALLATION (RH)
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
PBIC2901E
ROCKER COVER
EM-155
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ROCKER COVER
Exploded View
INFOID:0000000005274338
Removal and Installation
INFOID:0000000005274339
REMOVAL (LH)
1.
Remove the engine room cover. Refer to
EM-138, "Removal and Installation"
2.
Remove air duct and resonator assembly. Refer to
.
3.
Separate engine harness removing their brackets from rocker covers.
4.
Remove harness bracket from cylinder head, if necessary.
5.
Disconnect and remove the intake valve timing control solenoid valve (LH bank). Refer to
6.
Remove ignition coils. Refer to
EM-154, "Removal and Installation"
7.
Remove PCV hoses from rocker covers.
8.
Remove oil filler cap from rocker cover (LH), if necessary.
1.
Oil filler cap
2.
PCV hose
3.
PCV valve
4.
O-ring
5.
Rocker cover (RH)
6.
PCV hose
7.
Rocker cover gasket (RH)
8.
Rocker cover gasket (LH)
9.
Rocker cover (LH)
10. PCV hose
PBIC2905E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст