Nissan Pathfinder (2006 year). Instruction — part 146
ENGINE CONTROL SYSTEM
EC-27
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
●
During acceleration
The knock sensor retard system is designed only for emergencies. The basic ignition timing is programmed
within the anti-knocking zone, if recommended fuel is used under dry conditions. The retard system does not
operate under normal driving conditions. If engine knocking occurs, the knock sensor monitors the condition.
The signal is transmitted to the ECM. The ECM retards the ignition timing to eliminate the knocking condition.
Fuel Cut Control (at No Load and High Engine Speed)
UBS00K3A
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line.
SYSTEM DESCRIPTION
If the engine speed is above 1,800 rpm under no load (for example, the shift position is neutral and engine
speed is over 1,800 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off varies
based on engine speed.
Fuel cut will be operated until the engine speed reaches 1,500 rpm, then fuel cut will be cancelled.
NOTE:
This function is different from deceleration control listed under
EC-24, "Multiport Fuel Injection (MFI) System"
.
Sensor
Input Signal to ECM
ECM function
Actuator
Park/neutral position (PNP) switch
Neutral position
Fuel cut con-
trol
Fuel injector
Accelerator pedal position sensor
Accelerator pedal position
Engine coolant temperature sensor
Engine coolant temperature
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed
Wheel sensor
Vehicle speed*
EC-28
AIR CONDITIONING CUT CONTROL
2006 Pathfinder
AIR CONDITIONING CUT CONTROL
PFP:23710
Input/Output Signal Chart
UBS00K3B
*1: This signal is sent to the ECM through CAN communication line.
*2: ECM determines the start signal status by the signals of engine speed and battery voltage.
System Description
UBS00K3C
This system improves engine operation when the air conditioner is used.
Under the following conditions, the air conditioner is turned off.
●
When the accelerator pedal is fully depressed.
●
When cranking the engine.
●
At high engine speeds.
●
When the engine coolant temperature becomes excessively high.
●
When operating power steering during low engine speed or low vehicle speed.
●
When engine speed is excessively low.
●
When refrigerant pressure is excessively low or high.
Sensor
Input Signal to ECM
ECM function
Actuator
Air conditioner switch
Air conditioner ON signal*
1
Air conditioner
cut control
Air conditioner relay
Accelerator pedal position sensor
Accelerator pedal position
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
2
Engine coolant temperature sensor
Engine coolant temperature
Battery
Battery voltage*
2
Refrigerant pressure sensor
Refrigerant pressure
Power steering pressure sensor
Power steering operation
Wheel sensor
Vehicle speed*
1
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-29
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
PFP:18930
System Description
UBS00K3D
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line.
BASIC ASCD SYSTEM
Refer to Owner's Instruction for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any
malfunction occurs in ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET indicator in combination meter illuminates.)
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
●
CANCEL switch is pressed
●
More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)
●
Brake pedal is depressed
●
Selector lever is changed to N, P, R position
●
Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
●
VDC system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.
●
Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will
stop blinking and the cruise operation will be able to work by depressing SET/COAST switch or RESUME/
ACCELERATE switch.
●
Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
Sensor
Input signal to ECM
ECM function
Actuator
ASCD brake switch
Brake pedal operation
ASCD vehicle speed control
Electric throttle control
actuator
Stop lamp switch
Brake pedal operation
ASCD steering switch
ASCD steering switch operation
Park/Neutral position (PNP)
switch
Gear position
Wheel sensor
Vehicle speed*
TCM
Powertrain revolution*
EC-30
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
2006 Pathfinder
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is pressed after cancel operation other than depressing MAIN
switch is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition
must meet following conditions.
●
Brake pedal is released
●
Selector lever is in other than P and N positions
●
Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
Component Description
UBS00K3E
ASCD STEERING SWITCH
ASCD BRAKE SWITCH
and
.
STOP LAMP SWITCH
ELECTRIC THROTTLE CONTROL ACTUATOR
and
ASCD INDICATOR
CAN COMMUNICATION
EC-31
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
CAN COMMUNICATION
PFP:23710
System Description
UBS00K3F
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Refer to
, about CAN communication for detail.
EC-32
EVAPORATIVE EMISSION SYSTEM
2006 Pathfinder
EVAPORATIVE EMISSION SYSTEM
PFP:14950
Description
UBS00K3G
SYSTEM DESCRIPTION
The evaporative emission system is used to reduce hydrocarbons emitted into the atmosphere from the fuel
system. This reduction of hydrocarbons is accomplished by activated charcoals in the EVAP canister.
The fuel vapor in the sealed fuel tank is led into the EVAP canister which contains activated carbon and the
vapor is stored there when the engine is not operating or when refueling to the fuel tank.
The vapor in the EVAP canister is purged by the air through the purge line to the intake manifold when the
engine is operating. EVAP canister purge volume control solenoid valve is controlled by ECM. When the
engine operates, the flow rate of vapor controlled by EVAP canister purge volume control solenoid valve is
proportionally regulated as the air flow increases.
EVAP canister purge volume control solenoid valve also shuts off the vapor purge line during decelerating.
PBIB1631E
EVAPORATIVE EMISSION SYSTEM
EC-33
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
EVAPORATIVE EMISSION LINE DRAWING
PBIB2528E
EC-34
EVAPORATIVE EMISSION SYSTEM
2006 Pathfinder
BBIA0565E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст