Nissan Pathfinder (2006 year). Instruction — part 397
TROUBLE DIAGNOSES
WT-11
C
D
F
G
H
I
J
K
L
M
A
B
WT
2006 Pathfinder
TROUBLE DIAGNOSES
PFP:00004
Wiring Diagram — T/WARN —
EES00241
WEWA0060E
WT-12
TROUBLE DIAGNOSES
2006 Pathfinder
WEWA0021E
TROUBLE DIAGNOSES
WT-13
C
D
F
G
H
I
J
K
L
M
A
B
WT
2006 Pathfinder
Terminal and Reference Value (BCM)
EES00242
Refer to
WT-14
TROUBLE DIAGNOSES
2006 Pathfinder
ID Registration Procedure
EES00243
ID REGISTRATION WITH TRANSMITTER ACTIVATION TOOL
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected
during self-diagnosis depending on control unit which carries out CAN communication.
1.
With the ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to the data link con-
nector, then turn the ignition switch ON.
2.
Select "START (NISSAN BASED VHCL)".
3.
Touch “BCM” on "SELECT SYSTEM" screen.
NOTE:
If "BCM" is not indicated, go to
4.
Select “AIR PRESSURE MONITOR” on "SELECT TEST ITEM" screen.
5.
Select “WORK SUPPORT” on "SELECT DIAG MODE" screen,
and select "ID REGIST".
BCIA0029E
BCIA0030E
BCIA0031E
TROUBLE DIAGNOSES
WT-15
C
D
F
G
H
I
J
K
L
M
A
B
WT
2006 Pathfinder
6.
With the transmitter activation tool (J-45295) pushed against the
front left transmitter position of the tire air valve, press the button
for 5 seconds.
7.
Register the IDs in order from FR LH, FR RH, RR RH and RR LH. When ID registration of each wheel has
been completed, a buzzer sounds and the warning lamp flashes.
8.
After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results dis-
play will not function properly.
Tool number
:
—
(J-45295)
SEIA0101E
Activation tire position
Buzzer
Hazard warning lamp
CONSULT-II
1
Front LH
Once
2 times flashing
“YET”
↓
“DONE”
2
Front RH
2 times
3
Rear RH
3 times
4
Rear LH
4 times
WT-16
TROUBLE DIAGNOSES
2006 Pathfinder
ID REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1.
With the ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to the data link con-
nector, then turn the ignition switch ON.
2.
Select "START (NISSAN BASED VHCL)".
3.
Touch “BCM” on "SELECT SYSTEM" screen.
NOTE:
If "BCM" is not indicated, go to
4.
Select “AIR PRESSURE MONITOR” on “SELECT TEST ITEM"
screen.
5.
Select “WORK SUPPORT” on “SELECT DIAG MODE" screen,
and select "ID REGIST".
6.
Adjust the tire pressure to the values shown in the table below for ID registration, and drive the vehicle at
15 km/h (9.4 MPH) or more for a few minutes.
7.
After completing all ID registrations, press “END” to complete the procedure.
BCIA0029E
BCIA0030E
BCIA0031E
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front – Left
250 (2.5, 36)
Front – Right
230 (2.3, 33)
Rear – Right
210 (2.1, 30)
Rear – Left
190 (1.9, 27)
TROUBLE DIAGNOSES
WT-17
C
D
F
G
H
I
J
K
L
M
A
B
WT
2006 Pathfinder
8.
Inflate all tires to proper pressure. Refer to
WT-38, "SERVICE DATA AND SPECIFICATIONS (SDS)"
Activation tire position
CONSULT-II
Front LH
“YET”
↓
“DONE”
Front RH
Rear RH
Rear LH
WT-18
TROUBLE DIAGNOSES
2006 Pathfinder
Transmitter Wake Up Operation
EES00244
WITH TRANSMITTER ACTIVATION TOOL
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1.
With the transmitter activation tool (J-45295) pushed against the
front left transmitter, press the button for 5 seconds.
●
With ignition switch ON, as the warning lamp flashes per the
following diagram, the respective transmitter then must be
woken up.
2.
When the BCM finishes assigning each tire ID, the BCM flashes the hazard warning lamps and trailer
flasher lamps (if equipped) and sends flashing indicator status by CAN according to the following time
chart. Please see trailer flasher specification details of trailer flashing lamps since the BCM controls trailer
flasher lamps as brake lamps. Refer to
3.
After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out.
Tool number
:
—
(J-45295)
SEIA0101E
LEIA0059E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст