Nissan Pathfinder (2006 year). Instruction — part 345
SERVICE DATA AND SPECIFICATIONS (SDS)
MTC-113
C
D
E
F
G
H
I
K
L
M
A
B
MTC
2006 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Service Data and Specifications (SDS)
EJS004SS
COMPRESSOR
OIL
REFRIGERANT
ENGINE IDLING SPEED
Refer to
EC-75, "Idle Speed and Ignition Timing Check"
.
BELT TENSION
Refer to
.
Make
CALSONIC KANSEI CO. LTD.
Model
DKS-17D
Type
Swash plate
Displacement
144 cm
3
(8.79 in
3
) / revolution
Relief valve set pressure
3800
±
300 kPa (38.76
±
3.06 kg/cm
2
, 551.0
±
43.5 psi)
Direction of rotation
Clockwise (viewed from drive end)
Drive belt
Poly V ribbed
Description
NISSAN A/C System Oil Type S or equivalent
Capacity
180 m
(6.1 US fl oz, 6.3 Imp fl oz)
Type
HFC 134a (R-134a)
Capacity
0.70
±
0.05 kg (1.54
±
0.11 lb)
MTC-114
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
PB-1
PARKING BRAKE SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION
A
B
PB
2006 Pathfinder
PREPARATION . . . . . . . . . . . . . . ... 2
Commercial Service Tools . . . . . . . . . . 2
PARKING BRAKE SYSTEM . . . . . . . . . .. 3
On-Vehicle Service . . . . . . . . . . . . ... 3
PARKING BRAKE CONTROL . . . . . . . . ... 4
Components . . . . . . . . . . . . . . . . 4
Removal and Installation . . . . . . . . . . .. 4
REMOVAL . . . . . . . . . . . . . . . . 4
INSTALLATION . . . . . . . . . . . . . . 5
PARKING BRAKE SHOE . . . . . . . . . . ... 6
Removal and Installation . . . . . . . . . . .. 6
SERVICE DATA AND SPECIFICATIONS (SDS) . . 9
Parking Drum Brake . . . . . . . . . . . . . 9
Parking Brake Control . . . . . . . . . . . .. 9
PB-2
PREPARATION
2006 Pathfinder
PREPARATION
PFP:00002
Commercial Service Tools
EFS0064A
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-21177-A)
Brake drum clearance gauge
Measuring rear rotor drum to parking
brake shoe clearance
Power tool
Loosening bolts and nuts
WFIA0167E
PBIC0190E
PARKING BRAKE SYSTEM
PB-3
C
D
E
G
H
I
J
K
L
M
A
B
PB
2006 Pathfinder
PARKING BRAKE SYSTEM
PFP:36010
On-Vehicle Service
EFS0064B
PEDAL STROKE
●
When parking brake pedal is operated with the specified force, make sure the stroke is within the specified
number of notches. Check by listening and counting the ratchet clicks.
INSPECTION
●
Make sure the components are attached properly, checking for looseness or backlash.
●
Check parking brake pedal assembly for bends, damage and cracks, and replace if necessary.
●
Check cable for wear and damage, and replace if necessary.
●
Check parking brake warning lamp switch for malfunction, and replace if necessary. Refer to
ADJUSTMENT
1.
Remove lower instrument panel LH. Refer to
IP-14, "LOWER INSTRUMENT PANEL LH"
.
2.
Partially engage parking brake pedal to access adjusting nut.
3.
Insert a deep socket wrench to rotate adjusting nut and loosen
cable until tension is sufficiently released. Then, disengage the
parking brake pedal.
4.
Remove the wheel and tire using power tool.
5.
Remove the rotor and measure inner diameter at widest point
using Tool.
6.
Transfer measurement less 0.6 mm to the parking brake shoes
and adjust accordingly.
7.
Using wheel nuts, secure the disc to the hub to prevent it from
tilting.
8.
Rotate disc rotor to make sure there is no drag.
9.
Adjust cable as follows:
a.
Operate pedal 10 or more times with a force of 490 N (50 kg,
110 lb).
b.
Rotate adjusting nut with deep socket to adjust pedal stroke to
specification.
c.
With parking brake pedal completely disengaged, make sure
there is no drag on the parking brake.
Pedal stroke
: 4
−
5 notches [under force of 196 N (20.0 kg, 44.1 lb)]
WFIA0165E
Tool number
:
—
(J-21177-A)
Pedal stroke
: 4
−
5 notches [under force of
196 N (20.0 kg, 44.1 lb)]
WFIA0166E
PB-4
PARKING BRAKE CONTROL
2006 Pathfinder
PARKING BRAKE CONTROL
PFP:36010
Components
EFS0064C
Removal and Installation
EFS0064D
REMOVAL
1.
Remove the lower instrument panel LH and center console. Refer to
2.
Remove the floor trim. Refer to
3.
Remove the parking brake control adjusting nut.
1.
Lock plate
2.
Pedal assembly
3.
Adjusting nut
4.
Left rear cable
5.
Right rear cable
6.
Pin
7.
Return spring
8.
Equalizer
9.
Front cable grommet
10. Front cable
LFIA0229E
PARKING BRAKE CONTROL
PB-5
C
D
E
G
H
I
J
K
L
M
A
B
PB
2006 Pathfinder
CAUTION:
Do not reuse adjusting nut after removing it.
4.
Remove the lock plate from the front cable.
5.
Remove front parking brake cable bolt and nut.
6.
Disconnect return spring from equalizer.
7.
Disconnect the front parking brake cable from the equalizer and remove front cable.
8.
Remove the rear disc rotors. Refer to
BR-32, "Removal and Installation of Brake Caliper and Disc Rotor"
.
9.
Remove parking brake shoes, and remove rear cable from toggle lever. Refer to
10. Remove equalizer from right and left rear cables.
11. Remove right and left rear cable bolts and nuts, then remove right and left rear cables.
INSTALLATION
●
Installation is in the reverse order of removal.
CAUTION:
Do not reuse adjusting nut after removing it.
●
Adjust parking brake. Refer to
.
PB-6
PARKING BRAKE SHOE
2006 Pathfinder
PARKING BRAKE SHOE
PFP:44060
Removal and Installation
EFS0064E
COMPONENTS
REMOVAL
WARNING:
Clean the brakes with a vacuum dust collector to minimize the hazard of airborne particles or other
materials.
NOTE:
Remove the disc rotor only with the parking brake pedal completely disengaged.
1.
Back plate
2.
Anchor
3.
Shoes
4.
Toggle lever
5.
Upper return spring
6.
Shoe hold-down spring
7.
Retainer
8.
Shoe hold-down pin
9.
Adjuster
10. Lower return spring
11.
Disc rotor
12. Adjuster access plug
LFIA0230E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст