Nissan Pathfinder (2006 year). Instruction — part 95
REMOTE KEYLESS ENTRY SYSTEM
BL-61
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
4.
HARNESS INSPECTION BETWEEN BCM AND REMOTE KEYLESS ENTRY RECEIVER
1.
Disconnect remote keyless entry receiver and BCM connectors.
2.
Check continuity between remote keyless entry receiver con-
nector M120 terminals 1, 2, 4 and BCM connector M18 termi-
nals 18, 19, 20.
3.
Check continuity between remote keyless entry receiver termi-
nals 1, 2 and 4 and ground.
OK or NG
OK
>> Replace remote keyless entry receiver.
NG
>> Repair or replace the harness between the remote keyless entry receiver and BCM.
ACC Power Check
EIS007PC
1.
CHECK ACC POWER
With CONSULT-II
Check "ACC ON SW" in DATA MONITOR mode with CONSULT–II. Refer to
.
Without CONSULT-II
Check voltage between BCM connector M18 terminal 11 and ground.
OK or NG
OK
>> ACC power circuit is OK.
NG
>> Check the following:
●
10A fuse [No. 4, located in fuse block (J/B)]
●
Harness for open or short.
1 - 18
: Continuity should exist
2 - 20
: Continuity should exist
4 - 19
: Continuity should exist
1 - Ground
: Continuity should not exist
2 - Ground
: Continuity should not exist
4 - Ground
: Continuity should not exist
WIIA0308E
Monitor Item
Condition
ACC ON SW
Ignition switch position is ACC : ON
Ignition switch position is OFF : OFF
PIIA3367E
Connec-
tor
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(–)
M18
11
Ground
ACC
Battery voltage
OFF
0
PIIA7002E
BL-62
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
IPDM E/R Operation Check
EIS007PD
1.
CHECK IPDM E/R INPUT VOLTAGE
Check voltage between IPDM E/R connector E122 terminal 45 and ground.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> GO TO 2.
2.
CHECK IPDM E/R INPUT VOLTAGE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R and horn relay.
3.
Check continuity between IPDM E/R connector E122 terminal 45 and horn relay connector H-1 terminal 1.
4.
Check continuity between IPDM E/R connector E122 terminal 45 and ground.
OK or NG
OK
>> Further inspection is necessary. Refer to
.
NG
>> Repair or replace harness.
Check Hazard Function
EIS007PE
1.
CHECK HAZARD WARNING LAMP
Does hazard indicator flash with hazard switch?
Yes or No
Yes
>> Hazard warning lamp circuit is OK.
No
>> Check hazard indicator. Refer to
LT-64, "TURN SIGNAL AND HAZARD WARNING LAMPS"
.
Check Horn Function
EIS007PF
First, perform the "SELF-DIAG RESULTS" in "BCM" with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated in "SELF-DIAG RESULTS" of "BCM".
1.
CHECK HORN FUNCTION
Does horn sound with horn switch?
Yes or No
Yes
>> Horn circuit is OK.
No
>> Check horn circuit. Refer to
.
Check Headlamp Function
EIS007PG
First, perform the "SELF-DIAG RESULTS" in "BCM" with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated in "SELF-DIAG RESULTS" of "BCM".
Connector
Terminal
Voltage (V)
(Approx.)
(+)
(–)
E122
45
Ground
Battery voltage
LIIA1053E
45 - 1
: Continuity should exist.
45 - Ground
: Continuity should not exist.
WIIA0679E
REMOTE KEYLESS ENTRY SYSTEM
BL-63
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
1.
CHECK HEADLAMP OPERATION
Does headlamp come on when turning lighting switch ON?
Yes or No
Yes
>> Headlamp operation circuit is OK.
No
>> Check headlamp circuit. Refer to
.
Check Room Lamp Illumination Function
EIS007PH
1.
CHECK ROOM LAMP ILLUMINATION FUNCTION
When room lamp switch is in DOOR position, open the front door LH or RH.
OK or NG
OK
>> System is OK.
NG
>> Check room lamp illumination circuit. Refer to
Room lamp and ignition keyhole illumination should illuminate.
BL-64
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
ID Code Entry Procedure
EIS007PI
KEYFOB ID SET UP WITH CONSULT-II
NOTE:
●
If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A
specific ID code can be erased with CONSULT-II. However, when the ID code of a lost keyfob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new keyfobs must be re-registered.
●
When registering an additional keyfob, the existing ID codes in memory may or may not be erased.
If five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the
new ID code is added and no ID codes are erased.
●
Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest
ID code will be erased.
●
Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries on CAN communication.
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
3.
Turn ignition switch ON.
4.
Touch “START (NISSAN BASED VHCL)”.
5.
Touch “BCM”.
If "BCM" is not indicated, refer to
BBIA0538E
BCIA0029E
BCIA0030E
REMOTE KEYLESS ENTRY SYSTEM
BL-65
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
6.
Touch “MULTI REMOTE ENT”.
7.
Touch “WORK SUPPORT”.
8.
The items are shown on the figure can be set up.
●
“REMO CONT ID REGIST”
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or
when additional keyfob is required.
●
“REMO CONT ID ERASUR”
Use this mode to erase a keyfob ID code.
●
“REMO CONT ID CONFIR”
Use this mode to confirm if a keyfob ID code is registered or
not.
LIIA0194E
BCIA0031E
LIIA1147E
BL-66
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
KEYFOB ID SET UP WITHOUT CONSULT-II
LIIA1670E
REMOTE KEYLESS ENTRY SYSTEM
BL-67
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
NOTE:
●
If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT-II. However, when the ID code of a lost keyfob is not known, all con-
troller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new
keyfobs must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased,
the ID codes of all remaining and/or new keyfobs must be re-registered.
●
When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five
ID codes are stored in memory, when an additional code is registered, only the oldest code is erased. If
less than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is
added and no ID codes are erased.
●
If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob.
●
Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.
●
Even if same ID code that is already in the memory is input, the same ID code can be entered. The code
is counted as an additional code.
Keyfob Battery Replacement
EIS007PJ
LIIA1514E
BL-68
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2006 Pathfinder
VEHICLE SECURITY (THEFT WARNING) SYSTEM
PFP:28491
Component Parts and Harness Connector Location
EIS007PK
LIIA2413E
1.
IPDM E/R E118, E119, E120, E121,
E122, E123, E124
2.
BCM M18, M19, M20
(view with instrument lower panel LH
removed)
3.
Key switch M27
4.
Horns E3, E162
(Behind front combination lamp LH)
5.
Front door lock assembly LH (key cylin-
der switch) D14
6.
Main power window and door lock/
unlock switch D7
Power window and door lock/unlock
switch RH D105
7.
Front door switch
LH B8
RH B108
8.
Rear door switch
LH B18
RH B116
9.
Back door switch D502
Back door lock actuator D508
10. Combination meter M24
11.
Glass hatch ajar switch D503
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст