Nissan Pathfinder (2006 year). Instruction — part 235
OIL PAN AND OIL STRAINER
EM-27
C
D
E
F
G
H
I
J
K
L
M
A
EM
2006 Pathfinder
OIL PAN AND OIL STRAINER
PFP:11110
Removal and Installation
EBS00QBT
REMOVAL (LOWER)
WARNING:
To avoid the danger of being scalded, do not drain engine oil when engine is hot.
1.
Drain engine oil. Refer to
.
2.
Remove oil pan (lower) as follows:
a.
Loosen bolts with power tool in reverse order as shown to
remove.
1.
Oil pan (upper)
2.
Oil pressure sensor
3.
O-ring
4.
Relief valve
5.
O-ring
6.
Oil cooler
7.
Connector bolt
8.
Oil filter
9.
Drain plug
10. Drain plug washer
11.
Oil pan (lower)
12. Rear cover plate
13. Oil strainer
14
O-ring
15. Oil level gauge guide
16. Oil level gauge
PBIC2883E
PBIC2890E
EM-28
OIL PAN AND OIL STRAINER
2006 Pathfinder
b.
Remove oil pan (lower) using Tool.
CAUTION:
●
Be careful not to damage the mating surfaces.
●
Do not insert screwdriver, this will damage the mating
surfaces.
NOTE:
Slide seal cutter (1) by tapping on the side (2) of the tool with
hammer.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION (LOWER)
1.
Install oil pan (lower) as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
●
Also remove old liquid gasket from mating surface of oil pan
(upper).
●
Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Apply a continuous bead of liquid gasket using Tool to the oil
pan (lower) as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
●
Tighten bolts in numerical order as shown.
2.
Install oil pan drain plug. Refer to
EM-27, "Removal and Installation"
.
3.
Installation is in the reverse order of removal.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC2888E
Tool number
: WS39930000 (
—
)
PBIC2889E
PBIC2890E
OIL PAN AND OIL STRAINER
EM-29
C
D
E
F
G
H
I
J
K
L
M
A
EM
2006 Pathfinder
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check engine oil level again. Refer to
.
REMOVAL (UPPER)
WARNING:
To avoid the danger of being scalded, do not drain engine oil when engine is hot.
1.
Remove engine cover with power tool. Refer to
.
2.
Remove air duct. Refer to
3.
Drain engine oil. Refer to
CAUTION:
●
Perform this step when engine is cold.
●
Do not spill engine oil on drive belts.
4.
Drain engine coolant. Refer to
MA-13, "Changing Engine Coolant"
CAUTION:
●
Perform this step when engine is cold.
●
Do not spill engine coolant on drive belts.
5.
Remove front final drive (4X4). Refer to
.
6.
Disconnect steering gear lower joint shaft bolt and steering gear mounting nuts and bolts, position out of
the way. Refer to
7.
Remove starter motor. Refer to
8.
Disconnect A/T fluid cooler tube brackets and position out of the way. Refer to
9.
Remove oil filter, as necessary. Refer to ! Hyper-link Error ! .
10. Remove oil cooler. Refer to
11. Remove oil pan (lower). Refer to
12. Remove oil strainer.
13. Remove transmission joint bolts which pierce oil pan (upper). Refer to
.
14. Remove rear cover plate.
15. Loosen bolts with power tool in reverse order as shown to
remove.
PBIC2887E
EM-30
OIL PAN AND OIL STRAINER
2006 Pathfinder
●
Insert Tool between oil pan (upper) and lower cylinder block.
Slide Tool by tapping on the side of Tool with hammer.
Remove oil pan (upper).
CAUTION:
Be careful not to damage mating surfaces.
16. Remove O-rings from bottom of lower cylinder block and oil
pump.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION (UPPER)
1.
Install oil pan (upper) as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
●
Also remove the old liquid gasket from mating surface of
lower cylinder block.
●
Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Install new O-rings on the bottom of lower cylinder block and oil
pump.
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC2885E
PBIC2884E
PBIC2885E
OIL PAN AND OIL STRAINER
EM-31
C
D
E
F
G
H
I
J
K
L
M
A
EM
2006 Pathfinder
c.
Apply a continuous bead of liquid gasket using Tool to the lower
cylinder block mating surfaces of oil pan (upper) to a limited por-
tion as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
CAUTION:
●
For bolt holes with mark, apply liquid gasket outside
the hole.
●
Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-
ter to area “A”.
●
Attaching should be done within 5 minutes after coating.
d.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both oil pan gaskets and O-rings.
●
Tighten bolts in numerical order as shown.
●
There are two types of bolts. Refer to the following for locating
bolts.
e.
Tighten transmission joint bolts. Refer to
AT-246, "TRANSMISSION ASSEMBLY"
2.
Install oil strainer to oil pan (upper).
3.
Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check engine oil level again. Refer to
.
Tool number
: WS39930000 (
—
)
PBIC2886E
M8
×
100 mm (3.97 in)
: 7, 11, 12, 13
M8
×
25 mm (0.98 in)
: Except the above
PBIC2887E
EM-32
IGNITION COIL
2006 Pathfinder
IGNITION COIL
PFP:22448
Removal and Installation
EBS00QBU
REMOVAL (LEFT BANK)
1.
Remove engine cover with power tool. Refer to
2.
Remove air cleaner case and air duct. (At the left bank side, remove ignition coil) Refer to
3.
Move aside harness, harness bracket, and hoses located above ignition coil.
4.
Disconnect harness connector from ignition coil.
5.
Remove ignition coil.
CAUTION:
Do not shock it.
INSTALLATION (LEFT BANK)
Installation is in the reverse order of removal.
REMOVAL (RIGHT BANK)
1.
Remove intake manifold collector with power tool. Refer to
2.
Move aside harness, harness bracket, and hoses located above ignition coil.
3.
Disconnect harness connector from ignition coil.
4.
Remove ignition coil.
CAUTION:
Do not shock it.
INSTALLATION (RIGHT BANK)
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
PBIC2901E
SPARK PLUG (PLATINUM-TIPPED TYPE)
EM-33
C
D
E
F
G
H
I
J
K
L
M
A
EM
2006 Pathfinder
SPARK PLUG (PLATINUM-TIPPED TYPE)
PFP:22401
Changing Spark Plugs (Platinum - Tipped Type)
EBS00T32
REMOVAL
1.
Remove the ignition coil. Refer to
EM-32, "Removal and Installation"
2.
Remove the spark plug using a suitable tool.
CAUTION:
Do not drop or shock it.
INSPECTION AFTER REMOVAL
●
Do not use a wire brush to clean the spark plug.
●
If plug tip is covered with carbon, spark plug cleaner may be used.
1.
Ignition coil
2.
Spark plug
PBIC2901E
SEM294A
SMA773C
Cleaner air pressure
: Less than 588 kPa (5.9 bar, 6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
EM-34
SPARK PLUG (PLATINUM-TIPPED TYPE)
2006 Pathfinder
●
Checking and adjusting plug gap is not required between
change intervals.
CAUTION:
Do not drop or shock the spark plug.
INSTALLATION
Installation is in the reverse order of removal.
●
Use standard type spark plug for normal conditions.
●
The hot type spark plug is suitable when fouling occurs with the standard type spark plug under conditions
such as:
–
Frequent engine starts
–
Low ambient temperatures
●
The cold type spark plug is suitable when spark knock occurs with the standard type spark plug under
conditions such as:
–
Extended highway driving
–
Frequent high engine revolution
CAUTION:
Do not drop or shock the spark plug.
SMA806CA
Make
NGK
Standard type
PLFR5A-11
Hot type
PLFR4A-11
Cold type
PLFR6A-11
Gap (nominal)
1.1 mm (0.043 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст