Nissan Pathfinder (2006 year). Instruction — part 31
ON-VEHICLE SERVICE
AT-239
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
8.
Install bolts A, B and C in control valve with TCM.
9.
Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3). Then tighten other bolts.
10. Tighten control valve with TCM bolts to the specified torque.
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clips.
15. Install oil pan to transmission case. Refer to
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5140E
SCIA5446E
SCIA7022E
AT-240
ON-VEHICLE SERVICE
2006 Pathfinder
16. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal.
20. Refill the A/T with fluid and check for fluid leakage. Refer to
24, "Changing the Automatic Transmission Fluid (ATF)"
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1.
Disconnect negative battery terminal.
2.
MA-24, "Changing the Automatic Transmission Fluid (ATF)"
3.
Remove oil pan and oil pan gasket. Refer to
4.
Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
5.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
6.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
SCIA5038E
SCIA5039E
SCIA5146E
SCIA5253E
ON-VEHICLE SERVICE
AT-241
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
7.
Remove bracket from A/T fluid temperature sensor 2.
Installation
1.
Install A/T fluid temperature sensor 2 to bracket.
2.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
3.
Connect A/T fluid temperature sensor 2 connector.
4.
Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5.
Install oil pan to transmission case. Refer to
6.
Connect the negative battery terminal.
7.
Refill the A/T with fluid and check for fluid leakage. Refer to
MA-24, "Changing the Automatic Transmis-
SCIA5264E
SCIA5264E
SCIA5253E
SCIA5146E
AT-242
ON-VEHICLE SERVICE
2006 Pathfinder
Rear Oil Seal
ECS00ELV
REMOVAL AND INSTALLATION
Removal
1.
Remove rear propeller shaft. Refer to
2.
Remove transfer from transmission (4WD models). Refer to
145, "Removal and Installation"
3.
Remove rear oil seal using suitable tool.
CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (4WD models).
Installation
1.
Install new rear oil seal into the extension case (2WD models) or
adapter case (4WD models) until it is flush with component face,
using suitable tool or Tool.
CAUTION:
●
Apply ATF to rear oil seal.
●
Do not reuse rear oil seal.
2.
Install transfer to transmission (4WD models). Refer to
3.
Install rear propeller shaft. Refer to
4.
Check the A/T fluid level and for fluid leakage. Refer to
"Checking the Automatic Transmission Fluid (ATF)"
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
AIR BREATHER HOSE
AT-243
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
AIR BREATHER HOSE
PFP:31098
Removal and Installation
ECS00ELW
4X2
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, do not to crush or block by folding or bending the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
LCIA0389E
AT-244
AIR BREATHER HOSE
2006 Pathfinder
4X4
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, do not to crush or block by folding or bending the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
LCIA0390E
A/T FLUID COOLER
AT-245
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
A/T FLUID COOLER
PFP:21600
Removal and Installation
ECS00FSJ
Refer to the figure below for A/T cooler removal and installation.
●
After completing installation, check fluid leakage and fluid level. Refer to
AT-13, "Checking the Automatic
1.
A/T fluid cooler
2.
Fluid cooler tube
3.
Clip
4.
Hose clamp
5.
Cooler hose (lower)
6.
Cooler hose
7.
Tube joint
8.
Cooler hose (upper)
A.
To transmission
B.
From radiator
LCIA0400E
AT-246
TRANSMISSION ASSEMBLY
2006 Pathfinder
TRANSMISSION ASSEMBLY
PFP:31020
Removal and Installation (2WD)
ECS00ELX
COMPONENTS
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
1.
Disconnect the negative battery terminal.
2.
Remove the A/T fluid indicator.
3.
Remove the LH fender protector.
1.
A/T fluid indicator
2.
A/T fluid indicator pipe
3.
O-ring
4.
Insulator
5.
A/T crossmember
6.
Copper washer
7.
Bracket
8.
A/T fluid cooler tube
9.
Front crossmember
10.
Transmission assembly
A.
Self-sealing bolt
B.
Refer to installation.
WCIA0573E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст