Nissan Pathfinder (2006 year). Instruction — part 391
TROUBLE DIAGNOSIS
SRS-27
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2006 Pathfinder
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp or CONSULT-II each time repair is finished. If malfunction is still
observed, proceed to the next step. When malfunction is eliminated, further repair work is not required.
DIAGNOSTIC PROCEDURE 3
Final Check of SRS Using CONSULT-II—Diagnosis Mode
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected
in self-diagnosis depending on control unit which carries out CAN communication.
1.
After repairing SRS, connect both battery cables.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3.
Turn ignition switch ON.
BELT TENSION SENS
[UNIT FAIL]
[B1019]
●
Belt tension sensor is malfunctioning.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace RH front seat belt assem-
bly.
4. Replace RH front seat cushion/
occupant classification system con-
trol unit assembly.
5. Replace the related harness.
PASS A/B INDCTR CKT
[B1023]
●
Front passenger air bag off indicator is malfunctioning.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace front passenger air bag off
indicator.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
FRONTAL COLLISION
DETECTION
[B1209]
●
Driver and front passenger air bag modules are deployed.
1. Refer to
SIDE COLLISION
DETECTION
[B1210]
●
Side or curtain air bag modules are deployed (with side air
bags only).
1. Refer to
ROLLOVER DETECTION
[B1211]
●
Curtain air bag module and seat belt pre-tensioner are
deployed.
1. Refer to
Diagnostic item
Explanation
Repair order
Recheck SRS at each replacement
BBIA0538E
SRS-28
TROUBLE DIAGNOSIS
2006 Pathfinder
4.
Touch “START (NISSAN BASED VHCL)”.
5.
Touch “AIR BAG”.
If "AIR BAG" is not indicated, refer to
6.
Touch “SELF-DIAG [CURRENT]”.
7.
If no malfunction is detected on “SELF-DIAG [CURRENT]”,
repair of SRS is completed. Go to step 8.
If any malfunction is detected on “SELF-DIAG [CURRENT]”, the
malfunctioning part is not repaired completely or another mal-
functioning part is detected. Go to
, and repair malfunctioning part completely.
BCIA0029E
BCIA0030E
BCIA0031E
SRS701
TROUBLE DIAGNOSIS
SRS-29
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2006 Pathfinder
8.
Touch “ERASE”.
NOTE:
Touch “ERASE” to clear the memory of the malfunction
(“SELF-DIAG [PAST]”).
If the memory of the malfunction in “SELF-DIAG [PAST]” is not
erased, the User mode shows the system malfunction by the
operation of the warning lamp even if the malfunction is repaired
completely.
9.
Touch “BACK” key of CONSULT-II to “SELECT DIAG MODE”
screen. Touch “SELF-DIAG [PAST]”.
10. Check that no malfunction is detected on “SELF-DIAG [PAST]”.
11. Touch “BACK” key of CONSULT-II until “SELECT SYSTEM”
appears in order to return to User mode from Diagnosis mode.
12. Turn ignition switch OFF then turn off and disconnect CON-
SULT-II.
SRS-20, "Checking SRS Operation Using “AIR BAG”
.
WHIA0152E
BCIA0031E
SRS702
SRS-30
TROUBLE DIAGNOSIS
2006 Pathfinder
DIAGNOSTIC PROCEDURE 4 (CONTINUED FROM DIAGNOSTIC PROCEDURE 2)
Check SRS Repair History
1.
CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes
>> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
after repair. Go to
SRS-27, "DIAGNOSTIC PROCEDURE 3"
No
>> Go to
SRS-22, "DIAGNOSTIC PROCEDURE 2"
DIAGNOSTIC PROCEDURE 5
Check SRS Intermittent Malfunction Using CONSULT-II—Diagnosis Mode
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected
in self-diagnosis depending on control unit which carries out CAN communication.
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3.
Turn ignition switch ON.
4.
Touch “START (NISSAN BASED VHCL)”.
5.
Touch “AIR BAG”.
If "AIR BAG" is not indicated, refer to
BBIA0538E
BCIA0029E
BCIA0030E
TROUBLE DIAGNOSIS
SRS-31
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2006 Pathfinder
6.
Touch “SELF-DIAG [PAST]”.
7.
If diagnostic codes are displayed on “SELF-DIAG [PAST]”, go to
step 10.
If no malfunction is detected on “SELF-DIAG [PAST]”, touch
“BACK” and go back to “SELECT DIAG MODE”.
8.
Touch “TROUBLE DIAG RECORD”.
NOTE:
With “TROUBLE DIAG RECORD”, diagnosis results previ-
ously erased by a reset operation can be displayed.
9.
Diagnostic code is displayed on “TROUBLE DIAG RECORD”.
10. Touch “PRINT”.
11. Compare diagnostic codes to
SRS-32, "CONSULT-II Diagnostic
Code Chart ("SELF-DIAG [PAST]" or "TROUBLE DIAG
RECORD")"
12. Touch “BACK” key of CONSULT-II until “SELECT SYSTEM”
appears.
13. Turn ignition switch OFF, then turn off and disconnect CON-
SULT-II, and both battery cables.
BCIA0031E
WHIA0152E
SRS702
BCIA0031E
WHIA0153E
SRS-32
TROUBLE DIAGNOSIS
2006 Pathfinder
14. Repair the system as outlined by the “Repair order” in “Intermittent Malfunction Diagnostic Code Chart”,
that corresponds to the self-diagnostic result. For replacement procedure of component parts, refer to the
Removal and Installation procedure for the appropriate component.
15. Go to
SRS-27, "DIAGNOSTIC PROCEDURE 3"
, for final checking.
CONSULT-II Diagnostic Code Chart ("SELF-DIAG [PAST]" or "TROUBLE DIAG RECORD")
Diagnostic item
Explanation
Repair order
Recheck SRS at each replacement
NO DTC IS DETECTED
When malfunction is
indicated by the “AIR
BAG” warning lamp in
User mode.
●
Low battery voltage (Less than
9V)
●
Go to
●
Self-diagnostic result “SELF-DIAG
[PAST]” (previously stored in the
memory) might not be erased
after repair.
●
Intermittent malfunction has been
detected in the past.
●
Go to
CEDURE 4 (CONTINUED FROM
DIAGNOSTIC PROCEDURE 2)"
●
Go to
●
No malfunction is detected.
—
DRIVER AIRBAG MODULE
[OPEN]
[B1049] or [B1054]
●
Driver air bag module circuit is open (including the spiral
cable).
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace driver air bag module.
4. Replace the spiral cable.
5. Replace the air bag diagnosis sen-
sor unit.
6. Replace the related harness.
DRIVER AIRBAG MODULE
[VB-SHORT]
[B1050] or [B1055]
●
Driver air bag module circuit is shorted to some power sup-
ply circuit (including the spiral cable).
DRIVER AIRBAG MODULE
[GND-SHORT]
[B1051] or [B1056]
●
Driver air bag module circuit is shorted to ground (including
the spiral cable).
DRIVER AIRBAG MODULE
[SHORT]
[B1052] or [B1057]
●
Driver air bag module circuits are shorted to each other.
ASSIST A/B MODULE
[OPEN]
[B1065] or [B1070]
●
Front passenger air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace front passenger air bag
module.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
ASSIST A/B MODULE
[VB-SHORT]
[B1066] or [B1071]
●
Front passenger air bag module circuit is shorted to some
power supply circuit.
ASSIST A/B MODULE
[GND-SHORT]
[B1067] or [B1072]
●
Front passenger air bag module circuit is shorted to
ground.
ASSIST A/B MODULE
[SHORT]
[B1068] or [B1073]
●
Front passenger air bag module circuits are shorted to
each other.
CRASH ZONE SEN
[UNIT FAIL]
[B1033] or [B1034]
CRASH ZONE SEN
[COMM FAIL]
[B1035]
●
Crash zone sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace the crash zone sensor.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
TROUBLE DIAGNOSIS
SRS-33
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2006 Pathfinder
SIDE MODULE LH
[OPEN]
[B1134]
●
Front LH side air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace front LH seat back assem-
bly (front LH side air bag module).
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
SIDE MODULE LH
[VB-SHORT]
[B1135]
●
Front LH side air bag module circuit is shorted to some
power supply circuit.
SIDE MODULE LH
[GND-SHORT]
[B1136]
●
Front LH side air bag module circuit is shorted to ground.
SIDE MODULE LH
[SHORT]
[B1137]
●
Front LH side air bag module circuits are shorted to each
other.
SIDE MODULE RH
[OPEN]
[B1129]
●
Front RH side air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace front RH seat back assem-
bly (front RH side air bag module).
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
SIDE MODULE RH
[VB-SHORT]
[B1130]
●
Front RH side air bag module circuit is shorted to some
power supply circuit.
SIDE MODULE RH
[GND-SHORT]
[B1131]
●
Front RH side air bag module circuit is shorted to ground.
SIDE MODULE RH
[SHORT]
[B1132]
●
Front RH side air bag module circuits are shorted to each
other.
SATELLITE SENS LH
[UNIT FAIL]
[B1118] or [B1119]
SATELLITE SENS LH
[COMM FAIL]
[B1120]
●
LH side air bag (satellite) sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace the LH side air bag (satel-
lite) sensor.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
SATELLITE SENS RH
[UNIT FAIL]
[B1113] or [B1114]
SATELLITE SENS RH
[COMM FAIL]
[B1115]
●
RH side air bag (satellite) sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace the RH side air bag (satel-
lite) sensor.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
PRE-TEN FRONT LH
[OPEN]
[B1086]
●
The circuit for front LH seat belt pre-tensioner is open.
1. Visually check the wiring harness
connections.
2. Replace the harness if it has visible
damage.
3. Replace front LH seat belt pre-ten-
sioner.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
PRE-TEN FRONT LH
[VB-SHORT]
[B1087]
●
The circuit for front LH seat belt pre-tensioner is shorted to
some power supply circuit.
PRE-TEN FRONT LH
[GND-SHORT]
[B1088]
●
The circuit for front LH seat belt pre-tensioner is shorted to
ground.
PRE-TEN FRONT LH
[SHORT]
[B1089]
●
The circuits for the front LH seat belt pre-tensioner are
shorted to each other.
Diagnostic item
Explanation
Repair order
Recheck SRS at each replacement
SRS-34
TROUBLE DIAGNOSIS
2006 Pathfinder
PRE-TEN FRONT RH
[OPEN]
[B1081]
●
The circuit for front RH seat belt pre-tensioner is open.
1. Visually check the wiring harness
connections.
2. Replace the harness if it has visible
damage.
3. Replace front RH seat belt pre-ten-
sioner.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
PRE-TEN FRONT RH
[VB-SHORT]
[B1082]
●
The circuit for front RH seat belt pre-tensioner is shorted to
some power supply circuit.
PRE-TEN FRONT RH
[GND-SHORT]
[B1083]
●
The circuit for front RH seat belt pre-tensioner is shorted to
ground.
PRE-TEN FRONT RH
[SHORT]
[B1084]
●
The circuits for the front RH seat belt pre-tensioner are
shorted to each other.
FR CURTN MODULE LH
[OPEN]
[B1198]
●
The circuit for LH side front curtain air bag module is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace LH side curtain air bag
module.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
FR CURTN MODULE LH
[VB-SHORT]
[B1199]
●
The circuit for LH side front curtain air bag module is
shorted to some power supply circuits.
FR CURTN MODULE LH
[GND-SHORT]
[B1200]
●
The circuit for LH side front curtain air bag module is
shorted to ground.
FR CURTN MODULE LH
[SHORT]
[B1201]
●
The circuits for the LH side front curtain air bag module are
shorted to each other.
FR CURTN MODULE RH
[OPEN]
[B1193]
●
The circuit for RH side front curtain air bag module is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace RH side curtain air bag
module.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
FR CURTN MODULE RH
[VB-SHORT]
[B1194]
●
The circuit for RH side front curtain air bag module is
shorted to some power supply circuits.
FR CURTN MODULE RH
[GND-SHORT]
[B1195]
●
The circuit for RH side front curtain air bag module is
shorted to ground.
FR CURTN MODULE RH
[SHORT]
[B1196]
●
The circuits for the RH side front curtain air bag module are
shorted to each other.
CURTAIN MODULE LH
[OPEN]
[B1150]
●
The circuit for LH side rear curtain air bag module is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace LH side curtain air bag
module.
4. Replace the air bag diagnosis sen-
sor unit.
5. Replace the related harness.
CURTAIN MODULE LH
[VB-SHORT]
[B1151]
●
The circuit for LH side rear curtain air bag module is
shorted to some power supply circuits.
CURTAIN MODULE LH
[GND-SHORT]
[B1152]
●
The circuit for LH side rear curtain air bag module is
shorted to ground.
CURTAIN MODULE LH
[SHORT]
[B1153]
●
The circuits for the LH side rear curtain air bag module are
shorted to each other.
Diagnostic item
Explanation
Repair order
Recheck SRS at each replacement
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст