Nissan Pathfinder (2006 year). Instruction — part 87
BCM (BODY CONTROL MODULE)
BCS-25
C
D
E
F
G
H
I
J
L
M
A
B
BCS
2006 Pathfinder
6.
Touch “R51/D40/N51” and "OK" on “VEHICLE SELECT” screen.
For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
NOTE:
Confirm vehicle model on IDENTIFICATION PLATE. Refer to
7.
Touch “WRITE CONFIGURATION” on “SELECT CONFIG
ITEM” screen.
8.
Touch "YES”.
For canceling, touch "NO".
9.
Using the following flow chart, identify the correct model and configuration list. Confirm and/or change set-
ting value for each item according to the configuration list.
Depending on CONSULT-II software version being used, some or all of the write configuration items
shown in the following configuration lists may be displayed. If an item does not appear on the CONSULT-
II "WRITE CONFIGURATION" screen(s), then it is an auto setting item and it cannot be instructionly set or
changed.
NOTE:
Confirm vehicle model on IDENTIFICATION PLATE. Refer to
10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
CAUTION:
Make sure to touch "CHNG SETTING" even if the indicated configuration of new BCM is same as
the desirable configuration.
If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
LKIA0613E
LKIA0547E
LKIA0175E
ITEM
SET VAL
AUTO LIGHT
WITH
⇔
WITHOUT
DTRL
WITH
⇔
WITHOUT
BCS-26
BCM (BODY CONTROL MODULE)
2006 Pathfinder
11. Touch “OK” on "WRITE CONFIGURATION" screen.
If "CANCEL" is touched, it will return to previous screen.
12. Wait until the next screen during setting.
13. WRITE CONFIGURATION results are printed out automatically.
Confirm "WRITE CONFIGURATION" is correctly executed by
comparing sheet automatically printed out with applicable con-
figuration list shown in step 9.
14. Touch "OK" on "WRITE CONFIGURATION" screen.
WRITE CONFIGURATION is completed.
LKIA0397E
LKIA0398E
LKIA0509E
LKIA0400E
BCM (BODY CONTROL MODULE)
BCS-27
C
D
E
F
G
H
I
J
L
M
A
B
BCS
2006 Pathfinder
Removal and Installation
EKS00G0S
BCM
Removal
NOTE:
If possible, before removing BCM, retrieve current BCM configuration to use for reference when configuring
brand-new BCM after installation. Refer to
1.
Disconnect battery negative terminal.
2.
Remove lower instrument panel LH. Refer to
IP-14, "LOWER INSTRUMENT PANEL LH"
.
3.
Remove knee protector. Refer to
IP-10, "Removal and Installation"
.
4.
Remove BCM screws and release BCM.
5.
Disconnect BCM connectors and then remove BCM.
Installation
Installation is in the reverse order of removal.
NOTE:
●
When replacing BCM, it must be configured. Refer to
●
When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to
BL-100, "NVIS(NISSAN Vehicle Immobilizer System-NATS)"
.
●
When replacing BCM, perform ID registration procedure of low tire pressure warning system. Refer to
WT-14, "ID Registration Procedure"
●
When replacing BCM, register the remote keyless entry system keyfob ID codes. Refer to
●
When replacing BCM, perform adjustment procedure for the steering angle sensor. Refer to
"Adjustment of Steering Angle Sensor Neutral Position"
LKIA0564E
BCS-28
BCM (BODY CONTROL MODULE)
2006 Pathfinder
BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
BL
2006 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 4
PREPARATION . . . . . . . . . . . . . . ... 5
Special service tool . . . . . . . . . . . . .. 5
Commercial Service Tool . . . . . . . . . . . 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 6
Work Flow . . . . . . . . . . . . . . . . 6
Generic Squeak and Rattle Troubleshooting . . ... 8
Diagnostic Worksheet . . . . . . . . . . . 10
HOOD . . . . . . . . . . . . . . . . . ... 12
Fitting Adjustment . . . . . . . . . . . . .. 12
REMOVAL . . . . . . . . . . . . . . ... 14
INSTALLATION . . . . . . . . . . . . ... 14
Hood Lock Control Inspection . . . . . . . . 15
POWER DOOR LOCK SYSTEM . . . . . . . .. 16
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . 16
REMOTE KEYLESS ENTRY SYSTEM . . . . . . 41
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . . 41
INPUTS . . . . . . . . . . . . . . . ... 41
OPERATED PROCEDURE . . . . . . . . . 42
“MULTI REMOTE ENT” . . . . . . . . . ... 50
CONSULT-II Application Items . . . . . . . ... 51
BL-2
2006 Pathfinder
Pre-Diagnosis Inspection . . . . . . . . . . 53
BCM POWER SUPPLY AND GROUND CIRCUIT
INSPECTION . . . . . . . . . . . . . ... 53
Trouble Diagnoses . . . . . . . . . . . . .. 54
SYMPTOM CHART . . . . . . . . . . . . 54
KEYFOB ID SET UP WITH CONSULT-II . . . 64
KEYFOB ID SET UP WITHOUT CONSULT-II . . 66
Keyfob Battery Replacement . . . . . . . . .. 67
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 68
CONSULT-II INSPECTION PROCEDURE . . .. 79
CONSULT-II APPLICATION ITEM . . . . . ... 80
Trouble Diagnosis . . . . . . . . . . . . ... 81
WORK FLOW . . . . . . . . . . . . . .. 81
DOOR . . . . . . . . . . . . . . . . . . 90
Fitting Adjustment . . . . . . . . . . . . ... 90
Removal and Installation . . . . . . . . . . 92
FRONT DOOR LOCK . . . . . . . . . . . ... 95
Component Structure . . . . . . . . . . . ..95
Removal and Installation . . . . . . . . . . .95
REMOVAL . . . . . . . . . . . . . . . 95
INSTALLATION . . . . . . . . . . . . . 97
Disassembly and Assembly . . . . . . . . . 97
DOOR KEY CYLINDER ASSEMBLY . . . . ...97
REAR DOOR LOCK . . . . . . . . . . . . ..98
Component Structure . . . . . . . . . . . ..98
Removal and Installation . . . . . . . . . . .98
REMOVAL . . . . . . . . . . . . . . . 98
INSTALLATION . . . . . . . . . . . . . 98
BACK DOOR LOCK . . . . . . . . . . . . ..99
Component Structure . . . . . . . . . . . ..99
NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS) . . . . . . . . . . . . . . . . . ..100
Work Flow . . . . . . . . . . . . . . . .107
Trouble Diagnoses . . . . . . . . . . . . 108
HOMELINK UNIVERSAL TRANSCEIVER . . . . 119
Wiring Diagram — TRNSCV — . . . . . . . 119
Trouble Diagnoses . . . . . . . . . . . . 120
DIAGNOSTIC PROCEDURE . . . . . . . .120
CAB AND REAR BODY . . . . . . . . . . ..122
Body Mounting . . . . . . . . . . . . . ..122
BODY REPAIR . . . . . . . . . . . . . . 123
Body Exterior Paint Color . . . . . . . . . ..123
Body Component Parts . . . . . . . . . . .124
Corrosion Protection . . . . . . . . . . . .130
Body Sealing . . . . . . . . . . . . . . .133
BL-3
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
BODY CONSTRUCTION . . . . . . . . .. 136
Body Alignment . . . . . . . . . . . . . 137
Handling Precautions for Plastics . . . . . . 152
HANDLING PRECAUTIONS FOR PLASTICS .. 152
LOCATION OF PLASTIC PARTS . . . . . . 153
Precautions in Repairing High Strength Steel . .. 155
HIGH STRENGTH STEEL (HSS) USED IN NIS-
SAN VEHICLES . . . . . . . . . . . . 155
Foam Repair . . . . . . . . . . . . . . . 157
URETHANE FOAM APPLICATIONS . . . . 157
FILL PROCEDURES . . . . . . . . . . . 158
BL-4
PRECAUTIONS
2006 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EIS007O2
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for work
EIS007O3
●
After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check
their operation.
●
Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст