Nissan Pathfinder (2006 year). Instruction — part 98
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-85
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
2.
CHECK DOOR AND GLASS HATCH AJAR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door switch, glass hatch ajar switch and BCM.
3.
Check continuity between door switch connector (B) B8 (Front LH), B108 (Front RH), B18 (Rear LH),
B116 (Rear RH) terminal 2 or back door switch connector (C) D502 terminal 3 or glass hatch ajar switch
connector (D) D503 terminal 1 and BCM connector (A) M18, M19 terminals 12, 13, 42, 43, 47 and 48.
4.
Check continuity between door switch connector (B) B8 (Front
LH), B108 (Front RH), B18 (Rear LH), B116 (Rear RH) terminal
2 or back door switch connector (C) D502 terminal 3 or glass
hatch ajar switch connector (D) D503 terminal 1 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK DOOR AND GLASS HATCH AJAR SWITCHES
Check continuity between front/rear door switch connector (A) terminal 2 or back door switch connector (B)
terminal 3 or glass hatch ajar switch connector (C) terminal 1 and ground.
OK or NG
OK
>> Check switch case ground condition (front and rear door
and glass hatch) or ground circuit (back door).
NG
>> Replace door or glass hatch ajar switch.
1 - 42
: Continuity should exist.
2 - 47
: Continuity should exist.
2 - 12
: Continuity should exist.
2 - 48
: Continuity should exist.
2 - 13
: Continuity should exist.
3 - 43
: Continuity should exist.
1 - Ground
: Continuity should not exist.
2 - Ground
: Continuity should not exist.
3 - Ground
: Continuity should not exist.
WIIA0738E
Switch
Terminals
Condition
Continuity
A: Door switch
(front and rear)
2 – Ground
Open
Yes
Closed
No
B: Back door switch
1 – 3
Open
Yes
Closed
No
C: Glass hatch ajar
switch
1 – Ground
Open
Yes
Closed
No
WIIA0739E
BL-86
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2006 Pathfinder
Diagnostic Procedure 2
EIS007PW
SECURITY INDICATOR LAMP CHECK
1.
SECURITY INDICATOR LAMP ACTIVE TEST
With CONSULT-II
Check "THEFT IND” in "ACTIVE TEST" mode with CONSULT-II.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between BCM harness connector M18 terminal
23 and ground.
OK or NG
OK
>> Security indicator lamp is OK.
NG
>> GO TO 2.
2.
SECURITY INDICATOR LAMP CHECK
Check security indicator lamp condition. Refer to
DI-11, "SELF-DIAGNOSIS FUNCTION"
.
OK or NG
OK
>> GO TO 3.
NG
>> Replace combination meter. Refer to
LIIA0044E
Connector
Terminal
Security indi-
cator lamp
condition
Voltage (V)
(Approx.)
(+)
(-)
M18
23
Ground
Illuminated
0
Not illumi-
nated
Battery volt-
age
PIIA6230E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-87
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
3.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect BCM and combination meter connector.
3.
Check continuity between BCM connector M18 terminal 23 and
combination meter harness connector M24 terminal 39.
4.
Check continuity between BCM connector M18 terminal 23 and
ground.
OK or NG
OK
>> Check the following:
●
10A fuse [No. 19, located in fuse block (J/B)]
●
Harness for open or short between combination meter and fuse
NG
>> Repair or replace harness.
Diagnostic Procedure 3
EIS007PX
1.
CHECK DOOR KEY CYLINDER SWITCH LH
With CONSULT-II
Check front door lock assembly LH (key cylinder switch) ("KEY CYL LK-SW") and ("KEY CYL UN-SW") in
DATA MONITOR mode with CONSULT-II. Refer to
●
When key inserted in left front key cylinder is turned to LOCK:
●
When key inserted in left front key cylinder is turned to
UNLOCK:
Without CONSULT-II
Check voltage between BCM connector M18 terminals 7, 8 and
ground.
OK or NG
OK
>> Key cylinder switch signal is OK.
NG
>> GO TO 2.
23 - 39
: Continuity should exist.
23 - Ground
: Continuity should not exist.
WIIA0461E
KEY CYL LK-SW
: ON
KEY CYL UN-SW
: ON
LIIA0188E
Connector
Terminals
Condition of left front key
cylinder
Voltage (V)
(Approx.)
(+)
(–)
M18
7
Ground
Neutral/Lock
5
Unlock
0
8
Neutral/Unlock
5
Lock
0
WIIA0457E
BL-88
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2006 Pathfinder
2.
CHECK FRONT DOOR LOCK ASSEMBLY LH (KEY CYLINDER SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly LH (key cylinder switch).
3.
Check continuity between front door lock assembly LH (key cyl-
inder switch) connector terminals 3, 4 and 5.
OK or NG
OK
>> GO TO 3.
NG
>> Replace front door lock assembly LH (key cylinder switch). Refer to
.
3.
CHECK FRONT DOOR LOCK ASSEMBLY LH HARNESS
1.
Disconnect BCM.
2.
Check continuity between BCM connector M18 terminals 7, 8
and front door lock assembly LH connector D14 terminals 3, 5.
3.
Check continuity between BCM connector M18 terminals 7, 8
and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness
4.
CHECK FRONT DOOR LOCK ASSEMBLY LH GROUND
Check continuity between front door lock assembly LH connector
D14 terminal 4 and ground.
OK or NG
OK
BCS-27, "Removal and Installa-
.
NG
>> Repair or replace harness
Terminals
Condition
Continuity
4 – 5
Key is turned to LOCK.
Yes
Key is in N position or turned to
UNLOCK
No
3 – 4
Key is turned to UNLOCK.
Yes
Key is in N position or turned to LOCK
No
WIIA0458E
7 - 3
: Continuity should exist.
8 - 5
: Continuity should exist.
7 - Ground
: Continuity should not exist.
8 - Ground
: Continuity should not exist.
WIIA0676E
4 - Ground
: Continuity should exist.
WIIA0677E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-89
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
Diagnostic Procedure 4
EIS007PY
VEHICLE SECURITY HORN ALARM CHECK
1.
CHECK HORN OPERATION
Check if horn sounds with horn switch.
Does horn operate?
Yes
>> Check harness for open or short between IPDM E/R and horn relay.
No
>> Check horn circuit. Refer to
Diagnostic Procedure 5
EIS007PZ
VEHICLE SECURITY HEADLAMP ALARM CHECK
1.
CHECK VEHICLE SECURITY HEADLAMP ALARM OPERATION
Check if headlamps operate with lighting switch.
Do headlamps come on when turning switch ON?
Yes
>> Headlamp alarm is OK.
No
>> Check headlamp system. Refer to
.
Diagnostic Procedure 6
EIS007Q0
DOOR LOCK/UNLOCK SWITCH CHECK
1.
CHECK DOOR LOCK/UNLOCK SWITCH INPUT SIGNAL
Check if power door lock operates with door lock/unlock switch.
Do doors lock/unlock when using each door lock/unlock switch?
Yes
>> Door lock/unlock switch is OK.
No
BL-32, "Door Lock/Unlock Switch Check"
.
BL-90
DOOR
2006 Pathfinder
DOOR
PFP:80100
Fitting Adjustment
EIS007Q1
FRONT DOOR
Longitudinal clearance and surface height adjustment at front end
1.
2.
Loosen the hinge bolts. Raise or lower the front door at rear end to adjust.
3.
Install the fender. Refer to
REAR DOOR
Longitudinal clearance and surface height adjustment at front end
1.
Remove the center pillar upper finisher. Refer to
2.
Loosen the lower hinge bolts.
3.
From inside the vehicle, loosen the upper hinge nuts. Open the door, and raise or lower the rear end of the
door to adjust.
4.
Install the center pillar lower finisher. Refer to
.
A.
4.5
±
1.0 mm (0.177
±
0.039 in)
WIIA0732E
DOOR
BL-91
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
BACK DOOR
Longitudinal clearance and surface height adjustment
1.
Open and support the back door.
2.
Slightly loosen the hinge nuts.
3.
Reposition the door as necessary and tighten the nuts.
4.
Confirm the adjustment. Repeat as necessary to obtain the desired fit.
1.
Back door assembly
2.
Back door hinge
3.
Tail lamp assembly
4.
Rear bumper fascia
5.
Roof
6.
Side window glass
a.
7.2
±
2.0 mm (0.28
±
0.06 in)
b.
6.0
±
1.5 mm (0.24
±
0.06 in)
c.
2.0
±
2.0 mm ( 0.08
±
0.08 in)
d.
1.0
±
1.5 mm (0.04
±
0.06 in)
e.
8.0
±
1.5 mm (0.31
±
0.06 in)
f.
5.3
±
2.0 mm (0.21
±
0.08 in)
g.
0.8
±
2.0 mm (0.03
±
0.08 in)
h.
0.8
±
1.0 mm (0.03
±
0.04 in)
j.
2.0
±
1.0 mm (0.08
±
0.04 in)
WIIA0733E
BL-92
DOOR
2006 Pathfinder
STRIKER ADJUSTMENT
BODY SIDE DOORS
1.
Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
BACK DOOR
1.
Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
Removal and Installation
EIS007Q2
FRONT DOOR
CAUTION:
●
When removing and installing the door assembly, support the door with a jack and shop cloth to
protect the door and body.
●
When removing and installing door assembly, be sure to carry out the fitting adjustment.
●
Check the hinge rotating part for poor lubrication. If necessary, apply "body grease".
1.
Remove the front door glass and regulator. Refer to
GW-57, "FRONT DOOR GLASS AND REGULATOR"
.
2.
Remove the door harness.
3.
Remove the check link bolt from the hinge pillar.
4.
Remove the door-side hinge nuts, and the door assembly.
WIIA0734E
WIIA0735E
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст