Nissan Pathfinder (2006 year). Instruction — part 114
REAR DISC BRAKE
BR-35
C
D
E
G
H
I
J
K
L
M
A
B
BR
2006 Pathfinder
Thickness Inspection
Using a micrometer, check thickness of disc rotor. If thickness is
either at or below the wear limit, or exceeds maximum uneven wear,
replace disc rotor.
Brake Burnishing
EFS006G9
Burnish brake contact surface according to the following procedure after refinishing or replacing rotors, after
replacing pads, or if a soft pedal occurs at very low mileage.
CAUTION:
Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1.
Drive the vehicle on a straight smooth road at 50 km/h (31 MPH).
2.
Use medium brake pedal/foot effort to bring the vehicle to a complete stop from 50 km/h (31 MPH). Adjust
brake pedal/foot pressure such that vehicle stopping time equals 3 to 5 seconds.
3.
To cool brake system, drive the vehicle at 50 km/h (31 MPH) for 1 minute without stopping.
4.
Repeat steps 1 to 3, 10 times or more to complete the burnishing procedure.
Standard thickness
: 18.0 mm (0.709 in)
Wear limit
: 16.0 mm (0.630 in)
Maximum uneven wear
(measured at 8 positions)
: 0.015 mm (0.0006 in)
SBR020B
BR-36
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
EFS00644
Unit: mm (in)
Brake Pedal
EFS00645
Unit: mm (in)
Brake Booster
EFS00646
Unit: mm (in)
Front brake
Brake model
CLZ33VB
Rotor outer diameter
×
thickness
296
×
28 (11.654
×
1.102)
Pad Length
×
width
×
thickness
111.0
×
73.5
×
10.0 (4.73
×
2.894
×
0.394)
Cylinder bore diameter (each)
46.4 (1.83)
Rear brake
Brake model
CLZ14VB
Rotor outer diameter
×
thickness
308
×
18 (12.126
×
0.709)
Pad Length
×
width
×
thickness
83.0
×
33.0
×
11.0 (3.268
×
1.299
×
0.433)
Cylinder bore diameter
38.1 (1.50)
Control valve
Valve model
Electric brake force distribution
Brake booster
Booster model
C215T
Diaphragm diameter
215 (8.46)
Recommended brake fluid
Refer to
MA-11, "RECOMMENDED FLUIDS AND LUBRI-
.
Free height "H"
182.1 - 192.1 (7.17 - 7.56)
Depressed pedal height ("D" [under a force of 490 N (50 kg, 110 lb)
with engine running]
105 - 115 (4.13 - 4.53)
Clearance between pedal stopper and threaded end of stop lamp
switch and ASCD switch "C
1
" or “C
2
”
0.74 - 1.96 (0.029 - 0.077)
Pedal play "A"
3 - 11 (0.12 - 0.43)
WFIA0160E
Input rod installation standard dimension
15.6
−
15.9 (0.614
−
0.626)
SERVICE DATA AND SPECIFICATIONS (SDS)
BR-37
C
D
E
G
H
I
J
K
L
M
A
B
BR
2006 Pathfinder
Check Valve
EFS00647
Front Disc Brake
EFS00648
Unit: mm (in)
Rear Disc Brake
EFS00649
Unit: mm (in)
Vacuum leakage
[at vacuum of -66.7 kPa(-500 mmHg, -19.69 inHg)]
Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake model
CLZ33VB
Brake pad
Standard thickness (new)
10.0 (0.394)
Repair limit thickness
2.0 (0.079)
Disc rotor
Standard thickness (new)
28.0 (1.102)
Repair limit thickness
26.0 (1.024)
Maximum uneven wear (measured at 8 positions)
0.015 (0.0006)
Runout limit (with it attached to the vehicle)
0.05 (0.0020)
Brake model
CLZ14VB
Brake pad
Standard thickness (new)
11.0 mm (0.433 in)
Repair limit thickness
2.0 mm (0.079 in)
Disc rotor
Standard thickness (new)
18.0 mm (0.709 in)
Repair limit thickness
16.0 mm (0.630 in)
Maximum uneven wear (measured at 8 positions)
0.015 mm (0.0006 in)
Runout limit (with it attached to the vehicle)
0.07 mm (0.0028 in)
BR-38
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION
A
B
BRC
2006 Pathfinder
VDC/TCS/ABS
PRECAUTIONS . . . . . . . . . . . . . . .. 4
CHECK POINTS FOR USING CONSULT-II . . . 4
Precautions for Brake Control . . . . . . . . .. 5
Precautions for CAN System . . . . . . . . ... 6
PREPARATION . . . . . . . . . . . . . . ... 7
Special Service Tool . . . . . . . . . . . . . 7
Commercial Service Tools . . . . . . . . . . 7
SYSTEM DESCRIPTION . . . . . . . . . . . 8
ABS/EBD SYSTEM . . . . . . . . . . . . 10
VDC/TCS SYSTEM . . . . . . . . . . . . 10
Hydraulic Circuit Diagram . . . . . . . . . .. 10
CAN COMMUNICATION . . . . . . . . . . ...11
System Description . . . . . . . . . . . . .11
TROUBLE DIAGNOSIS . . . . . . . . . . . 12
How to Perform Trouble Diagnoses for Quick and
Accurate Repair . . . . . . . . . . . . . . 12
Component Parts and Harness Connector Location
ABS WARNING LAMP, SLIP INDICATOR LAMP
AND VDC OFF INDICATOR LAMP INSPECTION ... 24
For Fast and Accurate Diagnosis . . . . . . ... 25
PRECAUTIONS FOR DIAGNOSIS . . . . . . 25
REFERENCE VALUE FROM CONSULT-II . . . 26
CONSULT-II Function (ABS) . . . . . . . . .. 29
CONSULT-II BASIC OPERATION PROCEDURE
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS . . . . . . . . . . . . . . . . . . 38
VDC OFF SWITCH . . . . . . . . . . . . 52
TROUBLE DIAGNOSES FOR SYMPTOMS . . . 53
ABS Works Frequently . . . . . . . . . . ... 53
Unexpected Pedal Action . . . . . . . . . ... 54
BRC-2
2006 Pathfinder
ON-VEHICLE SERVICE . . . . . . . . . . . 58
Adjustment of Steering Angle Sensor Neutral Posi-
tion . . . . . . . . . . . . . . . . . . .. 58
WITH CONSULT-II . . . . . . . . . . . .. 58
WITHOUT CONSULT-II . . . . . . . . . ... 58
Calibration of Decel G Sensor . . . . . . . . 58
WHEEL SENSORS . . . . . . . . . . . . ... 60
Removal and Installation . . . . . . . . . . 60
REMOVAL . . . . . . . . . . . . . . ... 60
INSTALLATION . . . . . . . . . . . . . 60
SENSOR ROTOR . . . . . . . . . . . . . .. 61
Removal and Installation . . . . . . . . . . 61
FRONT . . . . . . . . . . . . . . . . 61
REAR . . . . . . . . . . . . . . . . ... 61
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 62
Removal and Installation . . . . . . . . . . 62
REMOVAL . . . . . . . . . . . . . . ... 62
INSTALLATION . . . . . . . . . . . . . 63
STEERING ANGLE SENSOR . . . . . . . . ... 64
Removal and Installation . . . . . . . . . . 64
G SENSOR . . . . . . . . . . . . . . . . 65
Removal and Installation . . . . . . . . . . 65
REMOVAL . . . . . . . . . . . . . . ... 65
INSTALLATION . . . . . . . . . . . . . 65
HDC/HSA/VDC/TCS/ABS
PRECAUTIONS . . . . . . . . . . . . . . . 66
CHECK POINTS FOR USING CONSULT-II . . 66
Precautions for Brake Control . . . . . . . . 67
Precautions for CAN System . . . . . . . . .. 68
PREPARATION . . . . . . . . . . . . . . . 69
Special Service Tool . . . . . . . . . . . ... 69
Commercial Service Tools . . . . . . . . . .. 69
SYSTEM DESCRIPTION . . . . . . . . . . .. 70
ABS/EBD SYSTEM . . . . . . . . . . . . 72
HDC/HSA SYSTEM . . . . . . . . . . . . 72
VDC/TCS SYSTEM . . . . . . . . . . . .72
Hydraulic Circuit Diagram . . . . . . . . . ...73
CAN COMMUNICATION . . . . . . . . . . ...74
System Description . . . . . . . . . . . . .74
TROUBLE DIAGNOSIS . . . . . . . . . . . 75
How to Perform Trouble Diagnoses for Quick and
Accurate Repair . . . . . . . . . . . . . ..75
For Fast and Accurate Diagnosis . . . . . . . 88
PRECAUTIONS FOR DIAGNOSIS . . . . . .88
REFERENCE VALUE FROM CONSULT-II . . ..89
CONSULT-II Function (ABS) . . . . . . . . ...93
CONSULT-II BASIC OPERATION PROCEDURE
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS . . . . . . . . . . . . . . . . . ..103
VDC OFF SWITCH . . . . . . . . . . . 120
HDS SWITCH . . . . . . . . . . . . . 120
BRC-3
C
D
E
G
H
I
J
K
L
M
A
B
BRC
2006 Pathfinder
TROUBLE DIAGNOSES FOR SYMPTOMS . . .. 121
ON-VEHICLE SERVICE . . . . . . . . . . . 128
Adjustment of Steering Angle Sensor Neutral Posi-
tion . . . . . . . . . . . . . . . . . ... 128
WITH CONSULT-II . . . . . . . . . . . 128
WITHOUT CONSULT-II . . . . . . . . . 128
Calibration of Decel G Sensor . . . . . . . .. 128
WHEEL SENSORS . . . . . . . . . . . . . 130
Removal and Installation . . . . . . . . . .. 130
REMOVAL . . . . . . . . . . . . . . . 130
INSTALLATION . . . . . . . . . . . . . 130
SENSOR ROTOR . . . . . . . . . . . . ... 131
Removal and Installation . . . . . . . . . .. 131
FRONT . . . . . . . . . . . . . . . .. 131
REAR . . . . . . . . . . . . . . . . 131
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) . 132
Removal and Installation . . . . . . . . . .. 132
REMOVAL . . . . . . . . . . . . . . . 132
INSTALLATION . . . . . . . . . . . . . 133
STEERING ANGLE SENSOR . . . . . . . . 134
Removal and Installation . . . . . . . . . .. 134
G SENSOR . . . . . . . . . . . . . . . .. 135
Removal and Installation . . . . . . . . . .. 135
REMOVAL . . . . . . . . . . . . . . . 135
INSTALLATION . . . . . . . . . . . . . 135
BRC-4
[VDC/TCS/ABS]
PRECAUTIONS
2006 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EFS0064H
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake System
EFS0064I
CAUTION:
●
Refer to
MA-11, "RECOMMENDED FLUIDS AND LUBRICANTS"
for recommended brake fluid.
●
Never reuse drained brake fluid.
●
Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
●
To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.
●
Never use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic
system.
●
Use flare nut wrench when removing and installing brake
tube.
●
If a brake fluid leak is found, the part must be disassembled
without fail. Then it has to be replaced with a new one if a
defect exists.
●
Turn the ignition switch OFF and remove the connector of
the ABS actuator and electric unit (control unit) or the bat-
tery terminal before performing the work.
●
Always torque brake lines when installing.
●
Burnish the brake contact surfaces after refinishing or
replacing rotors, after replacing pads, or if a soft pedal
occurs at very low mileage.
Refer to
(front disc brake) or
(rear disc
brake).
WARNING:
●
Clean brake pads and shoes with a waste cloth, then wipe with a dust collector.
Precautions When Using CONSULT-II
EFS0064J
When connecting CONSULT-II to data link connector, connect them through CONSULT-II CONVERTER.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
CHECK POINTS FOR USING CONSULT-II
1.
Has CONSULT-II been used without connecting CONSULT-II CONVERTER on this vehicle?
●
If YES, GO TO 2.
SBR686C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст