Nissan Pathfinder (2006 year). Instruction — part 360
POWER STEERING OIL PUMP
PS-23
C
D
E
F
H
I
J
K
L
M
A
B
PS
2006 Pathfinder
CAUTION:
●
Do not reuse the copper gaskets
●
Do not reuse the O-ring. Apply a coat of Genuine Nissan PSF or equivalent to the O-ring. Refer to
MA-11, "RECOMMENDED FLUIDS AND LUBRICANTS"
.
PS-24
HYDRAULIC LINE
2006 Pathfinder
HYDRAULIC LINE
PFP:49721
Removal and Installation
EGS0011P
Refer to the following illustration for hydraulic line removal and installation.
1.
Reservoir tank
2.
Suction hose
3.
High pressure hose
4.
Oil cooler
5.
Steering gear assembly
6.
Reservoir tank
LGIA0035E
HYDRAULIC LINE
PS-25
C
D
E
F
H
I
J
K
L
M
A
B
PS
2006 Pathfinder
7.
Reservoir tank bracket
8.
Return hose
9.
Hose clamps
10. Suction hose
11.
Connector bolts
12. Copper washers
PS-26
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Steering Wheel
EGS0011Q
Steering Column
EGS0011R
End play of the axle direction for steering wheel
0 mm (0 in)
Steering wheel turning force
39 N (4 kg-f, 9 lb-f) or less
Steering wheel play on the outer circumference
0
−
35 mm (0
−
1.38 in)
Steering column length “L1”
165.1 mm (6.500 in)
Steering column length “L2”
258.0 mm (10.16 in)
Tilt range "A"
73.8 mm (2.906 in)
SGIA0475E
WGIA0083E
SERVICE DATA AND SPECIFICATIONS (SDS)
PS-27
C
D
E
F
H
I
J
K
L
M
A
B
PS
2006 Pathfinder
Steering Outer Socket and Inner Socket
EGS0011S
Oil Pump
EGS0011T
Steering Fluid
EGS0011U
Steering gear type
PR26AM
Outer socket
Swinging torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Measurement on spring balance
●
Measuring point: cotter pin hole of stud
4.84
−
46.7 N (0.50
−
4.7 kg, 4
−
34 lb)
Rotating torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Axial end play
0.5 mm (0.020 in) or less
Inner socket
Swinging torque
1.0
−
7.8 N·m (0.11
−
0.79 kg-m, 9
−
69 in-lb)
Measurement on spring balance
●
Measuring point: L mark see above,
L=83.2 mm (3.276 in).
12.1
−
93.7 N (1.3
−
9.5 kg, 9
−
69 lb)
Axial end play
0.2 mm (0.08 in) or less
Tie-rod maximum length “L”
84.0 mm (3.31 in)
SGIA0358E
SGIA0167E
Oil pump relief hydraulic pressure
8.0
−
8.8 mPa (81.60
−
89.76 kg/cm
2
, 1160.0
−
1276.0 psi)
Fluid capacity
Approx. 1.0
(2 1/8 US pt, 1 3/4 Imp pt)
PS-28
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
RAX-1
REAR AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
A
B
RAX
2006 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools (SST) . . . . . . . . . . 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
WHEEL HUB . . . . . . . . . . . . . . . .. 5
On-Vehicle Inspection and Service . . . . . . .. 5
WHEEL BEARING INSPECTION . . . . . . . 5
Components . . . . . . . . . . . . . . . . 5
Removal and Installation . . . . . . . . . . .. 5
REMOVAL . . . . . . . . . . . . . . . . 5
INSTALLATION . . . . . . . . . . . . . . 6
REAR DRIVE SHAFT . . . . . . . . . . . . . 7
Components . . . . . . . . . . . . . . . . 7
Removal and Installation . . . . . . . . . . .. 7
Disassembly and Assembly . . . . . . . . . .. 8
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 13
Wheel Bearing . . . . . . . . . . . . . . 13
Drive Shaft . . . . . . . . . . . . . . . .. 13
RAX-2
PRECAUTIONS
2006 Pathfinder
PRECAUTIONS
PFP:00001
Caution
EDS003AH
Observe the following precautions when disassembling and servicing drive shaft.
●
Perform work in a location which is as dust-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
Prevention of the entry of foreign objects must be taken into account during disassembly of the service
location.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст