Nissan Pathfinder (2006 year). Instruction — part 187
DTC P0327, P0328, P0332, P0333 KS
EC-355
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
Wiring Diagram
UBS00K8A
BBWA2370E
EC-356
DTC P0327, P0328, P0332, P0333 KS
2006 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
UBS00K8B
1.
CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check resistance between ECM terminals 15, 36 and ground. Refer to Wiring Diagram.
NOTE:
It is necessary to use an ohmmeter which can measure more than 10 M
Ω
.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II
1.
Disconnect knock sensor harness connector.
2.
Check harness continuity between ECM terminal 15 and knock
sensor (bank1) terminal 1, ECM terminal 36 and knock sensor
(bank 2) terminal 1.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors F67, F150
●
Harness for open or short between ECM and knock sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK KNOCK SENSOR
EC-358, "Component Inspection"
OK or NG
OK
>> GO TO 5.
NG
>> Replace knock sensor.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
15
36
W
W
Knock sensor (Bank 1)
Knock sensor (Bank 2)
[Engine is running]
●
Idle speed
Approximately 2.5V
Resistance: Approximately 532 - 588 k
Ω
[at 20
°
C (68
°
F)]
Continuity should exist.
BBIA0547E
DTC P0327, P0328, P0332, P0333 KS
EC-357
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
5.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace ground connections.
6.
CHECK KNOCK SENSOR SHIELD CIRCUIT FOR OPEN AND SHORT
1.
Disconnect knock sensor harness connector.
2.
Check harness continuity between knock sensor terminal 2 and ground. Refer to Wiring Diagram.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors F67, F150
●
Harness connectors F14, E5
●
Harness for open or short between knock sensor and ground
>> Repair open circuit or short power in harness or connectors.
8.
CHECK INTERMITTENT INCIDENT
Refer to
EC-144, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
BBIA0539E
Continuity should exist.
EC-358
DTC P0327, P0328, P0332, P0333 KS
2006 Pathfinder
Component Inspection
UBS00K8C
KNOCK SENSOR
Check resistance between knock sensor terminal 1 and ground.
NOTE:
It is necessary to use an ohmmeter which can measure more
than 10 M
Ω
.
CAUTION:
Do not use any knock sensors that have been dropped or phys-
ically damaged. Use only new ones.
Removal and Installation
UBS00K8D
KNOCK SENSOR
Resistance: Approximately 532 - 588 k
Ω
[at 20
°
C (68
°
F)]
SEF111Y
DTC P0335 CKP SENSOR (POS)
EC-359
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
DTC P0335 CKP SENSOR (POS)
PFP:23731
Component Description
UBS00K8E
The crankshaft position sensor (POS) is located on the oil pan facing
the gear teeth (cogs) of the signal plate. It detects the fluctuation of
the engine revolution.
The sensor consists of a permanent magnet and Hall IC.
When the engine is running, the high and low parts of the teeth
cause the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor
changes.
The ECM receives the voltage signal and detects the fluctuation of
the engine revolution.
ECM receives the signals as shown in the figure.
CONSULT-II Reference Value in Data Monitor Mode
UBS00K8F
Specification data are reference values.
On Board Diagnosis Logic
UBS00K8G
DTC Confirmation Procedure
UBS00K8H
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V with igni-
tion switch ON.
PBIB0562E
PBIB2744E
MONITOR ITEM
CONDITION
SPECIFICATION
ENG SPEED
●
Run engine and compare CONSULT-II value with the tachometer
indication.
Almost the same speed as the tachometer
indication.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0335
0335
Crankshaft position
sensor (POS) circuit
●
The crankshaft position sensor (POS) signal
is not detected by the ECM during the first
few seconds of engine cranking.
●
The proper pulse signal from the crankshaft
position sensor (POS) is not sent to ECM
while the engine is running.
●
The crankshaft position sensor (POS) signal
is not in the normal pattern during engine
running.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Crankshaft position sensor (POS)
●
Signal plate
EC-360
DTC P0335 CKP SENSOR (POS)
2006 Pathfinder
WITH CONSULT-II
1.
Turn ignition switch ON and select “DATA MONITOR” mode with
CONSULT-II.
2.
Crank engine for at least 2 seconds and run it for at least 5 sec-
onds at idle speed.
3.
If 1st trip DTC is detected, go to
EC-362, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
DTC P0335 CKP SENSOR (POS)
EC-361
C
D
E
F
G
H
I
J
K
L
M
A
EC
2006 Pathfinder
Wiring Diagram
UBS00K8I
BBWA1752E
EC-362
DTC P0335 CKP SENSOR (POS)
2006 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
UBS00K8J
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
13
G
Crankshaft position sensor
(POS)
[Engine is running]
●
Warm-up condition
●
Idle speed
NOTE:
The pulse cycle changes depending on rpm
at idle
Approximately 10V
[Engine is running]
●
Engine speed: 2,000 rpm
Approximately 10V
111
BR
ECM relay
(Self shut-off)
[Engine is running]
[Ignition switch: OFF]
●
For a few seconds after turning ignition
switch OFF
0 - 1.5V
[Ignition switch: OFF]
●
More than a few seconds after turning igni-
tion switch OFF
BATTERY VOLTAGE
(11 - 14V)
119
120
R
P
Power supply for ECM
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14V)
PBIB1041E
PBIB1042E
BBIA0539E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст