Nissan Versa Note. Instruction — part 204
REMOTE KEYLESS ENTRY RECEIVER
DLK-101
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000009645329
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO for USA >>Refer to
DLK-101, "Diagnosis Procedure (For USA)"
.
NO for Canada>>Refer to
DLK-102, "Diagnosis Procedure (For Canada)"
.
Diagnosis Procedure (For USA)
INFOID:0000000009645330
Regarding Wiring Diagram information, refer to
DLK-36, "INTELLIGENT KEY SYSTEM : Wiring Diagram"
.
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1. Disconnect BCM and remote keyless entry receiver connectors.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M97
38
Ground
Push button ignition
ON
0-.5 Volt
Push button ignition
OFF or ACC
Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M97
38
M94
2
Yes
(+)
(–)
Continuity
BCM
Connector
Terminal
M97
38
Ground
No
DLK-102
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
NO
>> Repair or replace harness.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO-1 >> Check 10A fuse No. 10 [located in fuse block J/B].
NO-2 >> Repair or replace harness between BCM and 10A fuse No. 10.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
Check continuity between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> Replace remote keyless entry receiver. Refer to
DLK-181, "Removal and Installation"
NO
>> Repair or replace harness.
Diagnosis Procedure (For Canada)
INFOID:0000000009645331
Regarding Wiring Diagram information, refer to
.
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between remote keyless entry receiver connector and ground with oscilloscope.
(+)
(–)
Voltage
Approx.
Remote keyless entry receiver
Connector
Terminal
M94
1
Ground
Battery voltage
Remote keyless entry receiver
Ground
Continuity
Connector
Terminal
M94
4
Yes
REMOTE KEYLESS ENTRY RECEIVER
DLK-103
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 7
NO
>> GO TO 2
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1. Disconnect remote keyless entry receiver connector.
2. Check signal between remote keyless entry receiver connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 3
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1. Disconnect BCM connector.
2. Check continuity between BCM connector and remote keyless entry receiver connector.
3. Check continuity between BCM connector and ground.
Terminals
Condition
Signal
(Reference value)
(+)
(–)
Remote keyless entry
receiver connector
Terminal
M90
2
Ground
Waiting
(All doors closed)
When signal is received
(All doors closed)
JMKIA0064GB
JMKIA0065GB
Terminals
Signal
(Reference value)
(+)
(–)
Remote keyless
entry receiver
connector
Terminal
M90
4
Ground
JMKIA0064GB
BCM connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M97
19
M90
4
Yes
DLK-104
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES
>> Reconnect BCM, GO TO 4
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
Check continuity between remote keyless entry receiver connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 5
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
Check continuity between BCM connector and remote keyless entry receiver connector.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 3
1. Check continuity between BCM connector and remote keyless entry receiver connector.
2. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Repair or replace harness between BCM and remote keyless entry.
7.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI SIGNAL CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
BCM connector
Terminal
Ground
Continuity
M97
19
No
Remote keyless entry
receiver
connector
Terminal
Ground
Continuity
M90
1
Yes
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M97
18
M90
1
Yes
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M97
20
M90
2
Yes
BCM connector
Terminal
Ground
Continuity
M97
20
No
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M97
22
M90
3
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст