Nissan Versa Note. Instruction — part 438
FRONT BUMPER
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
AWKIA2515ZZ
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
0.0 (0.00)
2.0 (0.08)
4.0 (0.16)
B-B
Clearance
2.4 (0.09)
4.4 (0.17)
6.4 (0.25)
B-B
Surface height
-1.5 (-0.06)
0.5 (0.02)
1.99 (0.08)
C-C
Clearance
0.0 (0.00)
2.0 (0.08)
4.0 (0.16)
D-D
Clearance
0.0 (0.00)
1.5 (0.06)
3.0 (0.12)
D-D
Surface height
0.0 (0.00)
1.5 (0.06)
3.0 (0.12)
E-E
Clearance
0.01 (0.00)
2.0 (0.08)
4.0 (0.16)
F-F
Clearance
0.1 (0.00)
0.3 (0.01)
1.0 (0.04)
F-F
Surface height
-0.1 (0.00)
0.7 (0.03)
1.7 (0.07)
EXT-26
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000008969515
Removal and Installation
INFOID:0000000008969516
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
REMOVAL
1. Remove rear combination lamps (LH/RH). Refer to
EXL-105, "Removal and Installation"
.
1.
Rear bumper fascia side
bracket (LH)
2.
Rear bumper reinforcement support
(LH)
3.
Rear bumper closing (LH)
4.
Rear bumper fascia
5.
Rear bumper finisher
6.
Rear bumper fascia spacer
7.
Rear bumper reinforcement
8.
Rear bumper closing (RH)
9.
Rear bumper reinforcement
support (RH)
10. Rear bumper fascia side
bracket (RH)
A.
J nut
Pawl
AWKIA2520ZZ
REAR BUMPER
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2. Remove screws (A) and clip (B) from rear bumper closings (1)
(LH/RH).
3. Remove the rear bumper fascia upper bolt (A) (LH/RH) from
each side of the rear bumper fascia (1).
4. Remove rear bumper fascia lower clips.
5. Remove the rear bumper fascia from the rear bumper fascia
side brackets (LH/RH) by releasing the pawls as shown.
: Pawl
CAUTION:
When removing rear bumper fascia, two people are
required to avoid damaging.
6. Remove the following parts after removing rear bumper fascia (if necessary).
• Two clips each and rear bumper closings (LH/RH)
• Two screws and rear bumper finisher
• Rear bumper fascia spacers
• Two bolts each and rear bumper side brackets (LH/RH)
7. Remove rear bumper reinforcement nuts and rear bumper reinforcement (if necessary).
8. Remove rear bumper reinforcement support nuts from each and the rear bumper reinforcement supports
(LH/RH) (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation specifications.
• Fitting adjustment cannot be performed.
ALKIA2525ZZ
AWKIA2526ZZ
AWKIA2523ZZ
EXT-28
< REMOVAL AND INSTALLATION >
REAR BUMPER
ALKIA3207ZZ
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
0.1 (0.00)
0.3 (0.01)
1.0 (0.04)
B-B
Clearance
0.0 (0.00)
1.5 (0.06)
3.5 (0.14)
B-B
Surface height
-1.5 (-0.06)
0.5 (0.02)
2.5 (0.10)
C-C
Clearance
3.0 (0.12)
5.0 (0.20)
7.0 (0.28)
C-C
Surface height
-2.0 (-0.08)
-1.5 (-0.06)
3.5 (0.14)
D-D
Clearance
5.0 (0.20)
7.0 (0.28)
9.0 (0.35)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст