Nissan Versa Note. Instruction — part 247
FRONT DOOR
DLK-273
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Tighten door striker bolts to specification. Refer to
.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009645175
REMOVAL
1. Remove front fender. Refer to
DLK-268, "Removal and Installation"
2. Remove front door assembly. Refer to
DLK-270, "DOOR ASSEMBLY : Removal and Installation"
.
3. Remove front door hinge bolts (body side) and front door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to the hinge mating surface.
• After installation, perform the front door adjustment procedure. Refer to
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009645176
REMOVAL
1. Remove front door speaker. Refer to
AV-54, "Removal and Installation"
(BASE AUDIO),
(DISPLAY AUDIO) or
AV-242, "Removal and Installation"
(NAVIGATION).
2. Remove door check link bolt (body side).
3. Remove door check link bolts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close, lock/unlock operation.
• Check door check link rotating point for poor lubrication. If
necessary, apply a multi-purpose grease.
JMKIA8072ZZ
JMKIA8074ZZ
DLK-274
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
Exploded View
INFOID:0000000009645177
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009645179
CAUTION:
• Use two people when removing or installing rear door due to its heavy weight.
• When removing and installing rear door assembly, support door using a suitable tool.
REMOVAL
1. Remove rear door harness grommet (1) from body side outer
(2), then pull out rear door harness.
1.
Door sash rear tape
2.
Inside seal
3.
Door sash front tape
4.
Door upper hinge
5.
Door lower hinge
6.
Door check link
7.
Rear door panel
8.
Door striker
9.
Grommet
10. Body panel plug
AWKIA2570ZZ
JMKIA8083ZZ
REAR DOOR
DLK-275
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect the harness connector (A) from rear door.
3. Remove door check link bolt (body side).
4. Remove door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to the hinge mating surface.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After adjusting, apply touch-up paint (body color) to the head of door hinge nuts.
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
JMKIA8084ZZ
JMKIA8072ZZ
DLK-276
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009645180
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Remove center pillar lower finisher. Refer to
INT-25, "CENTER PILLAR LOWER FINISHER : Removal
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Striker bolt
7.
Front door hinge
8.
Rear door upper hinge
9.
Rear door lower hinge
AWKIA2493ZZ
Section
Measurement
Standard
A – A
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
B – B
Clearance
4.6
± 2.0 (0.18 ± 0.08)
Surface height
0.0
± 1.5 (0.0 ± 0.06)
C – C
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст