Nissan Versa Note. Instruction — part 424
EXL-80
< DTC/CIRCUIT DIAGNOSIS >
PARKING LAMP CIRCUIT
6. With the parking lamps ON, check voltage between the rear combination lamp connectors and ground.
7. With the parking lamps ON, check voltage between the license plate lamp connector and ground.
Are the inspection results normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK PARKING, LICENSE PLATE AND TAIL LAMP CIRCUIT (OPEN)
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front combination lamp harness con-
nector.
4. Check continuity between the IPDM E/R harness connector and the rear combination lamp harness con-
nector.
5. Check continuity between the IPDM E/R harness connector and license plate lamp connector.
(+)
(
−)
Voltage
Connector
Terminal
LH
E27
7
Ground
Battery voltage
E29
5
RH
E28
7
E30
5
(+)
(
−)
Voltage
Connector
Terminal
LH
B25
1
Ground
Battery voltage
RH
B27
(+)
(
−)
Voltage
Connector
Terminal
LH
D507
1
Ground
Battery voltage
RH
D508
Connector
Terminal
Connector
Terminal
Continuity
LH
E45
23
E27
7
Yes
E29
5
RH
E28
7
E30
5
Connector
Terminal
Connector
Terminal
Continuity
LH
E45
23
B25
1
Yes
RH
B27
Connector
Terminal
Connector
Terminal
Continuity
E45
23
D507
1
Yes
D508
PARKING LAMP CIRCUIT
EXL-81
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Are the inspection results normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace the harness or connector.
5.
CHECK PARKING, LICENSE AND TAIL LAMP GROUND CIRCUITS
1. Check continuity between the front combination lamp harness connectors and ground.
2. Check continuity between the rear combination lamp harness connectors and ground.
3. Check continuity between the license plate lamp harness connectors and ground.
Are the inspection results normal?
YES
>> Replace the malfunctioning lamp.
NO
>> Repair or replace the harness or connector.
Connector
Terminal
—
Continuity
LH
E27
8
Ground
Yes
E29
6
RH
E28
8
E30
6
Connector
Terminal
—
Continuity
LH
B25
6
Ground
Yes
RH
B27
Connector
Terminal
—
Continuity
B507
2
Ground
Yes
B508
EXL-82
< DTC/CIRCUIT DIAGNOSIS >
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Description
INFOID:0000000009694069
The BCM monitors inputs from the combination switch (high beam and turn signal switch) to determine when
to activate the turn signals. The BCM outputs voltage direction to the left and right turn signals during turn sig-
nal operation or both during hazard warning operation. The BCM sends a turn signal indicator request to the
combination meter via the CAN communication lines.
The BCM performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
Turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function Check
INFOID:0000000009694070
1.
CHECK TURN SIGNAL LAMP
CONSULT
1. Select FLASHER of BCM (FLASHER) active test item.
2. While operating the test items, check that the turn signal lamp blinks.
Does the turn signal lamp blink?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009694071
Regarding Wiring Diagram information, refer to
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.
Is the bulb OK?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector and the rear combination lamp connector.
3. Turn the ignition switch ON.
4. With turn signal switch operating, check the voltage between the front combination lamp harness connec-
tor and ground.
LH
: Turn signal lamp LH blinking
RH
: Turn signal lamp RH blinking
OFF
: The turn signal lamp OFF
(+)
(
−)
Voltage
Connector
Terminal
LH
E29
4
Ground
RH
E30
4
PKID0926E
TURN SIGNAL LAMP CIRCUIT
EXL-83
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
5. With turn signal switch operating, check the voltage between the rear combination lamp harness connec-
tor and ground.
Are the inspection results normal?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN
1. Turn the ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between the BCM harness connector and the front combination lamp connector.
4. Check continuity between the BCM harness connector and the rear combination lamp connector.
Are the inspection results normal?
YES
>> GO TO 4.
NO
>> Repair or replace the harness or connector.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between the BCM harness connector and ground.
(+)
(
−)
Voltage
Connector
Terminal
LH
B25
4
Ground
RH
B27
4
PKID0926E
Connector
Terminal
Connector
Terminal
Continuity
Front LH
M99 (With Intelligent Key)
60
E29
4
Yes
Front RH
61
E30
Front LH
M19 (Without Intelligent Key)
64
E29
Front RH
63
E30
Connector
Terminal
Connector
Terminal
Continuity
Rear LH
M99 (With Intelligent Key)
60
B25
4
Yes
Rear RH
61
B27
Rear LH
M19 (Without Intelligent Key)
64
B25
Rear RH
63
B27
Connector
Terminal
—
Continuity
LH
M99 (With Intelligent Key)
60
Ground
No
RH
61
LH
M19 (Without Intelligent Key)
64
RH
63
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст