Nissan Versa Note. Instruction — part 701
B2601 SHIFT POSITION
SEC-83
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
2.
CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and IPDM E/R har-
ness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to
Is DTC B2601 detected again?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Inspection End.
CVT shift selector (park position switch)
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M38
8
E47
80
Yes
SEC-84
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
B2602 SHIFT POSITION
DTC Logic
INFOID:0000000009705887
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine.
2. Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705888
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC in Self Diagnostic Result mode of ABS using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC OF COMBINATION METER
Check DTC in Self Diagnostic Result mode of METER/M&A using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Check voltage between CVT shift selector (park position switch) harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2602
SHIFT P DIAG
BCM detects the following status for 10 seconds.
• Selector lever is in the P position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Harness or connectors
[CVT shift selector (park position
switch) circuit is open or shorted.]
• CVT shift selector (park position
switch)
• Combination meter
B2602 SHIFT POSITION
SEC-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 4.
4.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness
connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
REPLACE BCM
1. Replace BCM. Refer to
PCS-31, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
6.
CHECK CVT SHIFT SELECTOR CIRCUIT
1. Disconnect BCM connector and IPDM E/R connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness
connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)
SEC-86, "Component Inspection"
.
Is the inspection result normal?
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (park position switch)
Connector
Terminal
M38
7
Ground
12
CVT shift selector (park position switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M38
7
M98
104
Yes
CVT shift selector (park position switch)
Ground
Continuity
Connector
Terminal
M38
7
No
CVT shift selector (park position switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M38
8
M97
37
Yes
CVT shift selector (park position switch)
Ground
Continuity
Connector
Terminal
M38
8
No
SEC-86
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
YES
>> GO TO 8.
NO
>> Replace CVT shift selector. Refer to
TM-229, "Removal and Installation"
8.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009705889
1.
CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift selector (park position switch) terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace CVT shift selector. Refer to
TM-229, "Removal and Installation"
CVT shift selector (park position switch)
Condition
Continuity
Terminal
7
8
Selector lever: P position
Selector button: Released
No
Selector button: Pressed
Yes
Selector lever: Other than P position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст