Nissan Versa Note. Instruction — part 677
SE-38
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
DRIVER SIDE : Seat Cushion
INFOID:0000000009639730
WARNING:
Always work from the side or back of the seatback, do not work in front of seat.
DISASSEMBLY
1. Remove the driver side front seat. Refer to
SE-20, "DRIVER SIDE : Removal and Installation"
2. Remove the lift lever (1) (if equipped).
a. Release pawls and remove the lift lever finisher.
b. Remove screws and the lift lever (2).
: Pawl
3. Remove snap ring (1) as shown (
) using a suitable tool, then
the recline lever (2).
4. Remove the seat cushion outer finisher (LH) (1).
a. Remove screw (A).
b. Pull to release metal clips as shown (
) and remove.
: Metal clip
5. Remove the seat belt buckle (LH). Refer to
SB-8, "FRONT SEAT BELT BUCKLE : Removal and Installa-
6. Remove the seat cushion outer finisher (RH) (1).
a. Remove screw (B).
b. Position seat cushion trim (A) aside.
c.
Slide seat cushion outer finisher (RH) rearward, as shown (
),
to release pawl and remove.
: Pawl
7. Remove the seat cushion from the seat frame.
AWJIA0932ZZ
JMJIA6005ZZ
JMJIA6006ZZ
AWJIA0933ZZ
FRONT SEAT
SE-39
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
a. Release the seatback trim J-clips (C) and seat cushion J-clips
(B) from the seat cushion frame.
b. Unclip the harness from the seat cushion frame.
NOTE:
Take note of harness routing and attachment location for correct
installation.
c. Remove bolts (A) and the seat cushion.
8. Remove seat cushion trim and seat cushion pad from the seat
cushion frame (1).
a. Release string at locations (A) from seat cushion frame.
: Front
b. Loosen string then remove the seat cushion trim and seat cush-
ion pad.
9. Remove the hog rings and separate the seat cushion trim (1)
from the seat cushion pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
CAUTION:
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
PASSENGER SIDE
ALJIA0997ZZ
JMJIA6008ZZ
ALJIA0990ZZ
PIIB3356J
SE-40
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
PASSENGER SIDE : Exploded View
INFOID:0000000009567632
PASSENGER SIDE : Seatback
INFOID:0000000009567498
WARNING:
• Always work from the side or back of the seatback, do not work in front of seat.
• Do not damage the, chute, connectors, retainers, clips, module harness or the side air bag module.
DISASSEMBLY
1. Remove the pasenger side front seat. Refer to
SE-22, "PASSENGER SIDE : Removal and Installation"
.
2. Remove the headrest.
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Chute rod
5.
Side air bag module
6.
Slide finisher rear (LH/RH)
7.
Recline lever
8.
Seat cushion outer finisher (RH)
9.
Seat frame
10. Seat cushion outer finisher (LH)
11. Seat belt buckle
12. Seat cushion pad
13. Seat cushion trim
14. Seatback pad
15. Seatback trim
ALJIA1239ZZ
FRONT SEAT
SE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. Release trim strap (A) from the seat frame.
4. Release the J-hook retainer (C), unzip seatback zippers (A) and
release J-clips (B).
5. Release the headrest holder locks as shown and remove.
CAUTION:
Before removing the headrest holder, check its orientation
(front/rear and right/left).
6. Remove and discard chute rod nuts (A), then route the chute rod
(1) through the opening and remove it from the chute (B).
CAUTION:
Do not reuse the chute rod nuts.
7. Unclip the side air bag module harness from the seat frame.
NOTE:
Take note of harness routing and attachment location for correct installation.
AWJIA0913ZZ
AWJIA1115ZZ
JMJIA4073ZZ
AWJIA0922ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст