Nissan Versa Note. Instruction — part 857
WCS-42
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000009654152
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000009654153
1.
CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to
WCS-39, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace parking brake switch. Refer to
PB-9, "Removal and Installation"
3.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Check the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Repair harness or connector.
Combination meter
Condition
Status
Brake warning lamp
When parking brake is applied
ON
When parking brake is released
OFF
WCS
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
WCS-43
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000009654154
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
INFOID:0000000009654155
1.
CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check operation of seat belt warning lamp in combination meter.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK SEAT BELT BUCKLE SWITCH LH SIGNAL CIRCUIT
Check the seat belt buckle switch LH signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SEAT BELT BUCKLE SWITCH LH
Check seat belt buckle switch LH. Refer to
WCS-37, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> Replace seat belt buckle switch LH. Refer to
SR-33, "Removal and Installation"
Combination meter
Condition
Status
Seat belt warning lamp
When seat belt LH (driver seat) is fastened
OFF
When seat belt LH (driver seat) is unfastened
ON
WCS-44
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000009654156
Light reminder warning chime does not sound even though headlamps are illuminated.
Diagnosis Procedure
INFOID:0000000009654157
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the Data Monitor for the METER/M&A and check the BUZZER monitor value.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Check the driver side door switch signal circuit. Refer to
(with Intelligent Key)
or
DLK-225, "Diagnosis Procedure"
(without Intelligent Key).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Check the driver side door switch. Refer to
DLK-96, "Component Inspection"
(without Intelligent Key).
Is the inspection result normal?
YES
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Replace driver side door switch. Refer to
DLK-175, "Removal and Installation"
(with Intelligent
Key) or
DLK-301, "Removal and Installation"
Monitor Item
Condition
Status
BUZZER
Under the condition of buzzer input
ON
Except above
OFF
WCS
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
WCS-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
Description
INFOID:0000000009654173
The key warning chime does not sound, when all of the following conditions are fulfilled.
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (front door switch LH ON)
Diagnosis Procedure
INFOID:0000000009654174
1.
CHECK BCM INPUT SIGNAL
1. Connect CONSULT.
2. Select the DATA MONITOR of BCM(BUZZER) and check the KEY ON SW monitor value. Refer to
85, "BUZZER : CONSULT Function (BCM - BUZZER)"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-127, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK KEY SWITCH SIGNAL CIRCUIT
Check the key switch signal circuit. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-127, "Removal and Installation"
.
NO
>> Check applicable parts, and repair or replace corresponding parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст