Nissan Versa Note. Instruction — part 622
PCS-98
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
PUSH-BUTTON IGNITION SWITCH
Component Function Check
INFOID:0000000009579030
1.
CHECK FUNCTION
1. Select PUSH SW in Data Monitor of BCM with CONSULT.
2. Check the push-button ignition switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Go to
.
Diagnosis Procedure
INFOID:0000000009579031
Regarding Wiring Diagram information, refer to
.
1.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector and IPDM E/R connector E47.
3. Check voltage between push-button ignition switch connector M25 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM)
1. Disconnect BCM connector M98.
2. Check continuity between BCM connector M98 and push-button ignition switch connector M25.
3. Check continuity between BCM connector M98 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
3.
CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)
Check voltage between IPDM E/R connector E47 and ground.
Test item
Condition
Status
PUSH SW
Push-button ignition switch is pressed
On
Push-button ignition switch is not pressed
Off
Push-button ignition switch
Ground
Voltage
(Approx.)
Connector
Terminal
M25
8
—
Battery voltage
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M98
76
M25
8
Yes
BCM
Ground
Continuity
Connector
Terminal
M98
76
—
No
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-99
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)
1. Disconnect BCM connector M98.
2. Check continuity between IPDM E/R connector E47 and push-button ignition switch connector M25.
3. Check continuity between IPDM E/R connector E47 and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness or connectors.
5.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch connector M25 and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness or connectors.
6.
CHECK PUSH-BUTTON IGNITION SWITCH
PCS-99, "Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace push-button ignition switch. Refer to
PCS-103, "Removal and Installation"
.
Component Inspection
INFOID:0000000009579032
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E47
81
—
Battery voltage
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E47
81
M25
8
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
E47
81
—
No
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
4
—
Yes
Push-button ignition switch terminals
Condition
Continuity
4 – 8
Pressed
Yes
Not pressed
No
PCS-100
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
NO
>> Replace push-button ignition switch.
PCS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
PCS-101
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
Description
INFOID:0000000009579033
Check that vehicle Operating Conditions are as listed in “Conditions of Vehicle” below before starting Diagno-
sis Procedure. Make sure to check each symptom in Diagnosis Procedure.
NOTE:
The engine start function, door lock function, power distribution system, and NATS-NVIS in the Intelligent Key
system are closely related to each other regarding control. The vehicle security function can operate only
when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• ENGINE START BY I-KEY in WORK SUPPORT is set to On. Refer to
PCS-68, "INTELLIGENT KEY : CON-
SULT Function (BCM - INTELLIGENT KEY)"
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000009579034
1.
PERFORM WORK SUPPORT
Perform INSIDE ANT DIAGNOSIS in Work Support of INTELLIGENT KEY with CONSULT. Refer to
"INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of BCM with CONSULT.
Are any DTCs detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch. Refer to
PCS-99, "Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст