Nissan Versa Note. Instruction — part 166
RADIATOR
CO-13
< PERIODIC MAINTENANCE >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
5. Check for engine coolant leaks. Repair if necessary.
CO-14
< REMOVAL AND INSTALLATION >
[HR16DE]
RADIATOR
REMOVAL AND INSTALLATION
RADIATOR
Exploded View
INFOID:0000000009444797
Removal and Installation
INFOID:0000000009444798
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the radiator cap. Slowly turn it a
quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Reservoir tank hose
2.
Reservoir tank cap
3.
Reservoir tank
4.
Mounting rubber (lower)
5.
O-ring
6.
Drain plug
7.
Radiator
8.
Cooling fan assembly
9.
Clamp
10. Radiator hose (lower)
11. Clamp
12. Oil cooler hose
13. Radiator hose to water outlet (upper) 14. Radiator cap adapter
15. Radiator cap
16. Radiator cap adapter bracket
17. Clamp
18. Radiator hose (upper) to radiator
19. Mounting rubber (upper)
20. CVT cooler hose
21. Clamp
21. Clamp
22. Clamp
23. CVT cooler hose
24. Clamp
A.
To water inlet
B.
To water outlet
C.
To oil cooler
AWBIA1614ZZ
RADIATOR
CO-15
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
1. Drain engine coolant. Refer to
CO-8, "Draining Engine Coolant"
.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
3. Disconnect battery negative terminal. Refer to
PG-67, "Removal and Installation (Battery)"
.
4. Remove radiator hose (lower).
5. Remove radiator hose (upper) from water outlet.
6. Remove the front under cover. Refer to
EXT-37, "FRONT UNDER COVER : Removal and Installation"
.
7. Remove the front grille. Refer to
EXT-29, "Removal and Installation"
.
8. Disconnect reservoir tank hose, and remove reservoir tank.
9. Disconnect harness connector from fan motor, and move harness aside.
10. Remove radiator core support (upper). Refer to
DLK-139, "RADIATOR CORE SUPPORT UPPER :
.
11. Remove the condenser bolts and place aside. Refer to
HA-29, "CONDENSER : Removal and Installa-
12. Remove radiator hose (upper) from radiator.
13. Remove cooling fan assembly. Refer to
CO-17, "Removal and Installation"
CAUTION:
Be careful not to damage or scratch the radiator.
14. Disconnect CVT cooler lines.
15. Remove the radiator from bottom of the vehicle.
CAUTION:
When removing, do not damage or scratch radiator core or A/C condenser.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse O-ring.
• Insert the radiator hose (1) all the way to the stopper (2) or by 33 mm (1.30 in) (hose without a stopper) as
shown.
• The correct orientation of the hose clamps are as shown.
*: Refer to the illustrations for the specific position for each hose clamp tab.
1.
Radiator hose
2.
Stopper
A.
Radiator side
B.
Engine side
JPBIA4294GB
Radiator hose
Hose end
Paint mark
Position of hose clamp
*
Radiator hose (upper)
Radiator side
Upper
A
Engine side
Upper
B
Radiator hose (lower)
Radiator side
Lower
C
Engine side
Upper
D
CO-16
< REMOVAL AND INSTALLATION >
[HR16DE]
RADIATOR
• The angle (b) created by the hose clamp pawl and the specified
line (A) must be within
±30° as shown.
• To install hose clamps (1), check that the dimension (A) from the
end of the hose clamp on the radiator hose to the hose clamp is
within the reference value.
CAUTION:
• When installing do not damage or scratch radiator core or A/C
condenser.
• Replace water hose clamp if it is removed.
• Use only Genuine NISSAN bolts for the cooling fan assembly
and strictly follow the tightening torque. Over tightening may
damage the radiator.
INSPECTION AFTER INSTALLATION
• Check for engine coolant leaks. Refer to
• Start and warm up the engine. Visually inspect for engine coolant leaks. Repair as necessary.
A. View A
B. View B
C. View C
D
View D
E. View E
f.
45
°
: Vehicle upper
JSBIA1299ZZ
JPBIA4295ZZ
Dimension (A)
: 3 – 7 mm (0.12 – 0.28 in)
JPBIA3527ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст