Nissan Versa Note. Instruction — part 214
RADIATOR CORE SUPPORT
DLK-141
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Using a suitable tool (A), suspend radiator and condenser to
prevent them from falling.
CAUTION:
Use care to avoid damaging radiator and condenser.
4. Remove bolts (A) and radiator core support lower (1).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA8030ZZ
ALKIA3181ZZ
DLK-142
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000008969440
Removal and Installation
INFOID:0000000009486664
CAUTION:
Use a shop cloths to protect the body from being damaged during removal and installation.
REMOVAL
1. Remove the front combination lamp. Refer to
EXL-99, "Removal and Installation"
2. Remove cowl top side cover. Refer to
3. Remove front fender bolts.
1.
Front fender
2.
Cowl top side cover
3.
Front fender insulator
4.
Front fender stiffener
Pawl
Clip
AWKIA2569ZZ
FRONT FENDER
DLK-143
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Remove front fender stiffener (2) by carefully pulling upper por-
tion of front fender (1) away from body.
: Front
CAUTION:
Use care when removing the front fender. The front fender
stiffener foam adheres the front fender to the body. Care-
fully release the stiffener foam or damage to front fender
may occur.
5. Remove front fender.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, apply touch-up paint (body color) to the head of front fender bolts.
• After installation, adjust the following components as necessary:
- Hood assembly: Refer to
DLK-136, "HOOD ASSEMBLY : Adjustment"
.
- Front door assembly: Refer to
DLK-145, "DOOR ASSEMBLY : Adjustment"
.
JMKIA5633ZZ
DLK-144
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
FRONT DOOR
Exploded View
INFOID:0000000008969441
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009486665
CAUTION:
• Use two people when removing or installing front door due to its heavy weight
• When removing and installing front door assembly, support the door using a suitable tool.
• Do not use air tools or electric tools for servicing.
• Before servicing, turn ignition switch off, disconnect both battery terminals and wait at least three
minutes.
REMOVAL
1. Disconnect the battery positive and negative terminals and wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove dash side finisher. Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
3. Disconnect the harness connectors from the front door.
4. Remove door check link bolt (body side).
5. Remove door hinge nuts (door side) and front door assembly.
INSTALLATION
1.
Inside seal
2.
Door sash front tape
3.
Grommet (driver side only)
4.
Door upper hinge
5.
Door lower hinge
6.
Door check link
7.
Front door panel
8.
Lower grommet
9.
Upper grommet
10. Door striker
11. Body panel plug
12. Door sash rear tape
AWKIA2492ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст