Nissan Versa Note. Instruction — part 642
PWC-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009561098
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009560301
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PREPARATION
PWC-5
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009560299
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
PWC-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009619466
A. View with LH front door finisher removed
B. View with LH rear door finisher removed
No.
Component parts
Function
1.
BCM
• Supplies power supply to power window switch.
• Controls retained power.
• Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
detailed installation location.
2.
Power window main switch
Refer to
PWC-7, "Power Window Main Switch"
.
3.
Front power window motor (driver side)
Refer to
.
ALKIA3202ZZ
COMPONENT PARTS
PWC-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Power Window Main Switch
INFOID:0000000009619467
• Power window main switch controls all power windows.
• Power window main switch integrates UP/DOWN switch, power
window lock switch, and door lock/unlock switch.
• Power window main switch controls the power window lock
function.
Power Window Switch
INFOID:0000000009619468
• Each power window switch transmits UP/DOWN signal to each
motor.
• Each power window switch transmits UP/DOWN signal from power
window main switch to each motor.
Power Window Motor
INFOID:0000000009619469
• Starts operation according to signals from power window main
switch (front driver side).
• Transmits front power window motor (driver side) rotation as a
pulse signal to power window main switch.
• Excepting power window motor for driver door, starts operation
according to signals from power window main switch or each
power window switches.
4.
Front door switch (driver side)
• Inputs door open/close condition to BCM.
• Refer to
DLK-19, "INTELLIGENT KEY SYSTEM : Door Switch"
for detailed in-
stallation location.
5.
Rear power window switch LH
.
6.
Rear power window motor LH
.
No.
Component parts
Function
ALKIA3203ZZ
ALKIA3204ZZ
JMKIA6528ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст