Nissan Versa Note. Instruction — part 80
BCS
ADDITIONAL SERVICE WHEN REPLACING BCM
BCS-57
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000008969261
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
Work Procedure
INFOID:0000000008969262
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
BCS-70, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Instruction selection” to write
vehicle specification. Refer to
>> GO TO 4.
4.
INITIALIZE BCM (NATS) (IF EQUIPPED)
Perform BCM initialization. (NATS)
>> WORK END
BCS-58
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
CONFIGURATION (BCM)
Description
INFOID:0000000008969263
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Instruction setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
Work Procedure
INFOID:0000000008969264
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT Configuration
1. Select "WRITE CONFIGURATION - Instruction selection".
2. Identify the correct model and configuration list. Refer to
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “SETTING”. Refer to
setting value.
4. Select "SETTING".
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5. When "COMMAND FINISHED", select "END".
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Instruction selection Writes the vehicle configuration with instruction selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
BCS
CONFIGURATION (BCM)
BCS-59
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration List
INFOID:0000000008969265
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
⇔: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
I-KEY SYS FREQUENCY TYPE
MODE1
—
TRANSIT MODE
WITH
—
STOP/START SYSTEM
MODE1
—
AUTO LIGHT
WITH
⇔ WITHOUT
—
BLOWE FAN SIG
MODE1
⇔ MODE2
• MODE1: With automatic air conditioner
• MODE2: With instruction air conditioner
BCS-60
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000009693593
LAN-24, "CAN COMMUNICATION SYSTEM : System Description"
.
DTC Logic
INFOID:0000000009693594
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result
procedure.
Diagnosis Procedure
INFOID:0000000009693595
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “SELF- DIAG RESULTS”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation instruction.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
When any listed module cannot communicate
with CAN communication signal continuously for
2 seconds or more with ignition switch ON
In CAN communication system, any item (or
items) of the following listed below is malfunc-
tioning.
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст