Nissan Versa Note. Instruction — part 785
TM-20
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded View
INFOID:0000000009417464
Removal and Installation
INFOID:0000000009417465
REMOVAL
1. Move the shift selector to the neutral position.
2. Remove the battery tray. Refer to
PG-68, "Removal and Installation (Battery Tray)"
.
3. Pull out and disconnect cables from shifter lever A and selector lever, using a suitable tool.
4. While pressing the lock of the selector cable in the direction of
the arrows shown, remove the selector cable from the cable
mounting bracket.
5. While pressing the lock of the shifter cable in the direction of the
arrows shown, remove the shifter cable from the cable mounting
bracket.
6. Remove cable mounting bracket from clutch housing.
7. Pull the shift selector handle upward to remove.
8. Remove center console assembly. Refer to
.
9. Pull out and disconnect each cable from the shift selector
assembly, using a suitable tool.
1.
Shifter lever A
2.
Selector lever
3.
Selector cable
4.
Shifter cable
5.
Cable mounting bracket
6.
Tapping bolt
7.
Bracket
8.
Grommet
9.
Shift selector assembly
10. Shift selector
11. Shift selector handle
JPDIC0789GB
JPDIC0793ZZ
CONTROL LINKAGE
TM-21
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
a. While pressing the lock of the selector cable in the direction of
the arrows shown, remove the selector cable from the shift
selector assembly.
b. While pressing the lock of the shifter cable in the direction of the
arrows shown, remove the shifter cable from the shift selector
assembly.
10. Remove the shift selector assembly.
11. Remove center muffler, exhaust front tube, and heat plate. Refer
12. Remove the bracket from the vehicle.
13. Remove the grommet and then remove the shifter cable and
selector cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install each cable without causing interference with other parts. Do not allow cable to bend less than
120 mm (4.72 in), or exceed 180 degree twist.
• Install boot of each cable without causing interference with other parts. Do not exceed 90 degree
twist.
• Fit boot to center console assembly and the groove on shift selector handle.
• To install the shift selector handle, press it onto the shift selector.
CAUTION:
• Do not reuse shift selector handle.
• Be careful with orientation of shift selector handle.
• Bolt hole is not threaded on new clutch housing. Self-tapping bolt is used to attach lock plate to clutch hous-
ing.
CAUTION:
Do not reuse self-tapping bolt.
• Insert each cable until it reaches the cable mounting bracket and shift selector assembly.
• Insert each cable until it reaches the shifter lever A and the selector lever.
• Move the shift selector to the neutral position.
Inspection
INFOID:0000000009417466
INSPECTION AFTER INSTALLATION
Shift Selector Handle
Check that the shift selector handle is installed in the right position.
Shifter Cable and Selector Cable
• Pull each cable in the removal direction to check that it does not disconnect from the cable mounting
bracket.
• Pull each cable in the removal direction to check that it does not disconnect from the shift selector assembly.
• Pull grommet in the removal direction to check that it does not disconnect from the vehicle.
Shift Selector Assembly and Shift Selector
• Check that there is no unusual noise, binding, bending, looseness, and interference when the shift selector
is moved to each position. If there is a malfunction, then repair or replace the malfunctioning part.
• Check that the shift selector smoothly returns to the neutral position after moving the shift selector from 1st
to 2nd gear and releasing it. If there is a malfunction, then repair or replace the malfunctioning part.
• Check that the shift selector smoothly returns to the neutral position after moving the shift selector from 5th
to the reverse gear position and releasing it. If there is a malfunction, then repair or replace the malfunction-
ing part.
JPDIC0793ZZ
TM-22
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000009417467
Removal and Installation
INFOID:0000000009417468
REMOVAL
1. Remove air cleaner case. Refer to
EM-26, "Removal and Installation"
.
2. Remove air breather hose from the 2-way connector.
CAUTION:
When removing air breather hose, be sure to hold 2-way connector securely.
3. Remove cap from air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install air breather hose. Do not bend hose tightly, which may result in pinching or clogging.
• Insert the air breather hose to the base of the 2-way connector.
1.
Cap
2.
Air breather hose
3.
2-way connector
JPDIC0788ZZ
5TH MAIN GEAR ASSEMBLY
TM-23
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5TH MAIN GEAR ASSEMBLY
Removal and Installation
INFOID:0000000009417469
REMOVAL
1. Move the shift selector to the 3rd gear position.
2. Disconnect the shifter cable and the selector cable from shifter lever A and selector lever. Refer to
CAUTION:
Do not move shifter lever A and selector lever to disconnect each cable.
3. Drain gear oil. Refer to
4. Remove fender protector (LH). Refer to
EXT-36, "Removal and Installation"
.
5. Remove the harness clamp (A) from rear housing (1).
6. Remove rear housing and O-ring.
CAUTION:
Remove in direction of input shaft (
) as shown. Rear
housing gear oil channel is inserted to input shaft center
hole.
7. Remove 5th main gear assembly. Refer to step 5 through 8 of
“Disassembly of TRANSAXLE ASSEMBLY”. Refer to
.
INSTALLATION
Installation is in the reverse order of removal.
• Shift into 3rd with shifter lever to install the 5th main gear assembly, referring to Step 36 to 39 of “Assembly
of TRANSAXLE ASSEMBLY” Refer to
• Install O-ring and the rear housing to the transaxle case and tighten the bolts to the specified torque. Refer
.
CAUTION:
• Do not reuse O-ring.
• Do not pinch O-ring when installing rear housing.
• Refill gear oil. Refer to
Inspection
INFOID:0000000009417470
INSPECTION AFTER INSTALLATION
• Check the operation of the control linkage. Refer to
.
• Check the gear oil level and for oil leaks. Refer to
.
JPDIC0734ZZ
SCIA1709J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст