Nissan Versa Note. Instruction — part 160
CL-10
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
REMOVAL AND INSTALLATION
CLUTCH PEDAL
Exploded View
INFOID:0000000009417427
Removal and Installation
INFOID:0000000009417428
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
2. Disconnect master cylinder rod end (
) from clutch pedal.
3. Disconnect ASCD cancel switch and clutch interlock switch harness connector
4. Remove harness clip from clutch pedal.
5. Remove clutch pedal nuts and remove clutch pedal.
6. Remove pedal pad from clutch pedal.
7. Remove clutch interlock switch and clip from clutch pedal.
8. Remove pedal stopper rubber from clutch pedal using a suitable tool.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Press master cylinder rod end into clutch pedal until it stops.
1.
Clutch pedal
2.
Pedal stopper rubber
3.
Pedal pad
4.
Clutch interlock switch
5.
Clip
6.
ASCD cancel switch
7.
Clip
Front
ALBIA1141ZZ
PCIB1491E
CLUTCH PEDAL
CL-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
Inspection and Adjustment
INFOID:0000000009417429
INSPECTION AFTER REMOVAL
• Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found,
replace clutch pedal.
• Check pedal stopper rubber. If damage or deformation is found, replace pedal stopper rubber.
• Check pedal pad. If wear or damage is found, replace pedal pad.
INSPECTION AND ADJUSTMENT AFTER INSTALLATION
Inspect the clutch interlock switch position and adjust as necessary. Refer to
CL-12
< REMOVAL AND INSTALLATION >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000009417430
Removal and Installation
INFOID:0000000009417431
CAUTION:
• Do not spill clutch fluid onto painted surfaces. If clutch fluid spills, wipe up immediately and wash
the affected area with water.
• Do not disassemble clutch master cylinder.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove battery. Refer to
PG-67, "Removal and Installation (Battery)"
.
2. Remove air cleaner and air duct. Refer to
EM-26, "Removal and Installation"
.
PCS-31, "Removal and Installation"
(WITH I-KEY) or
(WITHOUT I-KEY).
4. Remove ECM bracket nuts (A).
1.
Reservoir hose
2.
Master cylinder
JPDIB0222ZZ
: Front
JPDIB0233ZZ
CLUTCH MASTER CYLINDER
CL-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
5. Remove master cylinder rod end (
) from clutch pedal.
6. Use one of the following methods to remove reservoir hose from
master cylinder.
• Drain clutch fluid from reservoir tank and remove reservoir
hose. Refer to
.
• Remove hose from master cylinder.
7. Pull up the lock pin (1) from connector of master cylinder (2) and
separate clutch tube (3).
8. Rotate master cylinder clockwise by 45 degrees and then
remove master cylinder from the vehicle.
INSTALLATION
CAUTION:
Do not spill clutch fluid onto painted surfaces. If fluid spills, wipe up immediately and wash the
affected area with water.
1. With the nipple (1) rotated clockwise by 45 degrees, insert clutch
master cylinder into the mounting hole. Rotate the clutch master
cylinder counterclockwise by 45 degrees (A) as shown to secure
it. At this time, nipple is in the upward (B).
2. Install master cylinder rod end to clutch pedal.
CAUTION:
Press master cylinder rod end into clutch pedal until it
stops.
3. Install reservoir hose to master cylinder.
4. Press down the lock pin into connector of master cylinder until it
stops.
5. Install clutch tube into connector of master cylinder until it stops.
6. Fill with clutch fluid and bleed clutch hydraulic system. Refer to
.
7. Installation of the remaining components is in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000009417432
INSPECTION AFTER INSTALLATION
Check for clutch fluid leaks and check the fluid level. Refer to
.
PCIB1491E
JPDIB0169ZZ
JPDIB0114ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст