Nissan Versa Note. Instruction — part 841
TM-244
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
OUTPUT SPEED SENSOR
OUTPUT SPEED SENSOR
Exploded View
INFOID:0000000009019793
Removal and Installation
INFOID:0000000009019794
REMOVAL
1. Disconnect the harness connector from output speed sensor.
NOTE:
Lift up the vehicle and perform the work from rear of the transaxle assembly.
2. Remove the output speed sensor.
3. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009019795
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Check the CVT fluid level. Refer to
1.
Transaxle assembly
2.
Output speed sensor
3.
O-ring
Front
Genuine NISSAN CVT Fluid NS-3
JSDIA1882GB
DIFFERENTIAL SIDE OIL SEAL
TM-245
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000009019796
Removal and Installation
INFOID:0000000009019797
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the front drive shaft from the transaxle assembly. Refer to
FAX-19, "Removal and Installation"
2. Remove the differential side oil seal using suitable tool.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mating surfaces
of the transaxle case and converter housing.
INSTALLATION
1. Drive the differential side oil seal into the transaxle case side (A)
and converter housing side (B) using suitable tool to the speci-
fied dimension.
CAUTION:
• Be careful not to scratch the lip of the differential side oil seal
when press-fitting it.
• Do not reuse differential side oil seal.
• Apply Genuine NISSAN CVT Fluid NS-3 to the differential side
oil seal lip and around the oil seal.
2. Install the front drive shaft. Refer to
FAX-19, "Removal and Installation"
.
Inspection and Adjustment
INFOID:0000000009019798
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
1.
Transaxle assembly
2.
Differential side oil seal (left side)
3.
Differential side oil seal (right side)
Front
Genuine NISSAN CVT Fluid NS-3
JSDIA1888ZZ
Dimension (C)
: 1.8
± 0.5 mm (0.071 ± 0.020 in).
Dimension (D)
: 1.8
± 0.5 mm (0.071 ± 0.020 in).
JSDIA1836ZZ
TM-246
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
DIFFERENTIAL SIDE OIL SEAL
Adjust the CVT fluid level. Refer to
.
WATER HOSE
TM-247
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
WATER HOSE
Exploded View
INFOID:0000000009019799
Removal and Installation
INFOID:0000000009019800
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
CAUTION:
Perform these steps after the engine coolant temperature has cooled sufficiently.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove the hose clamp and pull out the water hose A.
2. Remove the hose clamp and pull out the water hose B.
3. Remove the hose clamp and pull out the water hose C.
4. Pull out the heater hose and remove the water bypass pipe.
5. Remove the heater thermostat assembly.
1.
Hose clamp
2.
Water hose A
3.
Clip
4.
Bracket A
5.
Bracket B
6.
CVT oil warner
7.
Water hose B
8.
Water bypass pipe
9.
Hose clamp
10. Water hose C
11. Water outlet
A.
To heater core
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JSDIA4111GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст