Nissan Versa Note. Instruction — part 118
BRC-36
< ECU DIAGNOSIS INFORMATION >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RR RH OUT SOL
Operation status of all solenoid valves
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
RR LH IN SOL
Operation status of all solenoid valves
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
RR LH OUT SOL
Operation status of all solenoid valves
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
EBD WARN LAMP
EBD warning lamp
(Note 2)
When EBD warning lamp is ON
On
When EBD warning lamp is OFF
Off
STOP LAMP SW
Brake pedal operation
When brake pedal is depressed
On
When brake pedal is not depressed
Off
MOTOR RELAY
Motor and motor relay operation
When the motor relay and motor are op-
erating
On
When the motor relay and motor are not
operating
Off
ACTUATOR RLY
Actuator relay operation
When the actuator relay is operating
On
When the actuator relay is not operating
Off
ABS WARN LAMP
ABS warning lamp
(Note 2)
When ABS warning lamp is ON
On
When ABS warning lamp is OFF
Off
OFF LAMP
VDC OFF indicator lamp
(Note 2)
When VDC OFF indicator lamp is ON
On
When VDC OFF indicator lamp is OFF
Off
OFF SW
VDC OFF switch
When VDC OFF switch is in ON
On
When VDC OFF switch is in OFF
Off
SLIP/VDC LAMP
SLIP indicator lamp
(Note 2)
When SLIP indicator lamp is ON
On
When SLIP indicator lamp is OFF
Off
BATTERY VOLT
Battery voltage supplied to the ABS actuator
and electric unit (control unit)
Ignition switch ON
10 – 16 V
GEAR
Instruction mode gear position determined by
TCM
1st gear
2nd gear
3rd gear
4th gear
5th gear
1
2
3
4
5
SLCT LVR POSI
Selector lever position.
Vehicle stopped
N/P
ENGINE SPEED
With engine running
When engine running
RPM
YAW RATE SEN
Yaw rate detected by yaw rate/side G sensor
When vehicle stop
Approx. 0 d/s
When vehicle turning
-75 to 75 d/s
R POSI SIG
Transmission range switch signal ON/OFF
condition
CVT shift position = R position
On
CVT shift position = other than R position
Off
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-37
< ECU DIAGNOSIS INFORMATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
N POSI SIG
Transmission range switch signal ON/OFF
condition
CVT shift position = N position
On
CVT shift position = other than N position
Off
P POSI SIG
Transmission range switch signal ON/OFF
condition
CVT shift position = P position
On
CVT shift position = other than P position
Off
CV1
ABS actuator cut valve 1
When the cut valve is active
On
When the cut valve is inactive
Off
CV2
ABS actuator cut valve 2
When the cut valve is active
On
When the cut valve is inactive
Off
SV1
ABS actuator suction valve
When the suction valve is active
On
When the suction valve is inactive
Off
SV2
ABS actuator suction valve 2
When the suction valve is active
On
When the suction valve is inactive
Off
ACCEL POS SIG
Throttle actuator opening/closing is dis-
played (linked with accelerator pedal)
Accelerator pedal not depressed (ignition
switch is ON)
0 %
Depress accelerator pedal (ignition
switch is ON)
0 - 100 %
SIDE G-SENSOR
Transverse G detected by side G sensor
Vehicle stopped
Approx. 0 m/s
2
Vehicle turning right
Negative value
(m/s
2
)
Vehicle turning left
Positive value
(m/s
2
)
STR ANGLE SIG
Steering angle detected by steering angle
sensor
Straight-ahead
Approx. 0
°
Steering wheel turned
–720 to 720
°
PRESS SENSOR
Brake fluid pressure detected by pressure
sensor
With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed
–40 to 300 bar
EBD SIGNAL
EBD operation
EBD is active
On
EBD is inactive
Off
ABS SIGNAL
ABS operation
ABS is active
On
ABS is inactive
Off
TCS SIGNAL
TCS operation
TCS is active
On
TCS is inactive
Off
VDC SIGNAL
VDC operation
VDC is active
On
VDC is inactive
Off
EBD FAIL SIG
EBD fail-safe signal
In EBD fail-safe
On
EBD is normal
Off
ABS FAIL SIG
ABS fail-safe signal
In ABS fail-safe
On
ABS is normal
Off
TCS FAIL SIG
TCS fail-safe signal
In TCS fail-safe
On
TCS is normal
Off
VDC FAIL SIG
VDC fail-safe signal
In VDC fail-safe
On
VDC is normal
Off
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
BRC-38
< ECU DIAGNOSIS INFORMATION >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Note 1: Confirm tire pressure is normal.
Note 2: On and off timing for warning lamps and indicator lamps.
• Refer to
BRC-21, "VDC/TCS/ABS : VDC Function"
.
• Refer to
BRC-23, "VDC/TCS/ABS : TCS Function"
• Refer to
BRC-25, "VDC/TCS/ABS : ABS Function"
• Refer to
BRC-26, "VDC/TCS/ABS : EBD Function"
Fail-safe
INFOID:0000000009364897
VDC AND TCS FUNCTIONS
VDC warning lamp in combination meter turns ON when a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC and TCS functions. However, ABS and EBD
functions operate normally.
ABS FUNCTION
ABS warning lamp and SLIP indicator lamp in combination meter turn ON when a malfunction occurs in sys-
tem [ABS actuator and electric unit (control unit)]. The control is suspended for VDC, TCS and ABS functions.
However, EBD functions operate normally.
EBD FUNCTION
ABS warning lamp, brake warning lamp and SLIP indicator lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC,
TCS, ABS and EBD functions.
CRANKING SIG
Crank operation
Crank is active
On
Crank is inactive
Off
FLUID LEV SW
Brake fluid level switch
When brake fluid level switch ON
On
When brake fluid level switch OFF
Off
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-39
< ECU DIAGNOSIS INFORMATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
DTC
Malfunction detected condition
Fail-safe condition
C1101
When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended:
• VDC
• ABS
• EBD (only when both rear wheels
are malfunctioning)
C1102
When an open circuit is detected in rear LH wheel sensor circuit.
C1103
When an open circuit is detected in front RH wheel sensor circuit.
C1104
When an open circuit is detected in front LH wheel sensor circuit.
C1105
• When a short circuit is detected in rear RH wheel sensor circuit.
• When power supply voltage of rear RH wheel sensor is in following state.
- Rear RH wheel sensor power supply voltage: 7.2 V
≥ Rear RH wheel sensor pow-
er supply voltage
• When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
• When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106
• When a short circuit is detected in rear LH wheel sensor circuit.
• When power supply voltage of rear LH wheel sensor is in following state.
- Rear LH wheel sensor power supply voltage: 7.2 V
≥ Rear LH wheel sensor power
supply voltage
• When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
• When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107
• When a short circuit is detected in front RH wheel sensor circuit.
• When power supply voltage of front RH wheel sensor is in following state.
- Front RH wheel sensor power supply voltage: 7.2 V
≥ Front RH wheel sensor
power supply voltage
• When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
• When installation of front RH wheel sensor or front RH wheel sensor rotor is not
normal.
C1108
• When a short circuit is detected in front LH wheel sensor circuit.
• When power supply voltage of front LH wheel sensor is in following state.
- Front LH wheel sensor power supply voltage: 7.2 V
≥ Front LH wheel sensor pow-
er supply voltage
• When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
• When installation of front LH wheel sensor or front LH wheel sensor rotor is not
normal.
C1109
• When ignition power supply voltage is in following state.
- Ignition power supply voltage: 10 V
≥ Ignition power supply voltage.
- Ignition power supply voltage: 16 V
≤ Ignition power supply voltage.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1110
When there is an internal malfunction in the ABS actuator and electric unit (control
unit).
C1111
When a malfunction is detected in motor or motor relay.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
C1115
When difference in wheel speed between any wheel and others is detected when
the vehicle is driven, because of installation of tires other than specified.
The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD
C1116
When stop lamp switch signal is not input when brake pedal operates.
The following functions are sus-
pended:
• VDC
• TCS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст