Nissan Versa Note. Instruction — part 399
EM-112
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
HOW TO SELECT PISTON AND BEARING
In grinding crankshaft pin to use undersize bearings, keep the
fillet R (A) [0.8 - 1.2 mm (0.031 - 0.047 in)].
Main Bearing
INFOID:0000000009444758
HOW TO SELECT MAIN BEARING
When New Cylinder Block and Crankshaft Are Used
1. “Main Bearing Selection Table” rows correspond to main bearing
housing grade on left side of cylinder block.
• If there is a corrected stamp mark (B) on cylinder block, use it
as a correct reference.
2. Apply main journal diameter grade stamped on crankshaft front
side to column in the “Main Bearing Selection Table”.
3. Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
4. Apply the symbol obtained to the “Main Bearing Grade Table” to select main bearing.
NOTE:
Service part is available as a set of both upper and lower.
When Cylinder Block and Crankshaft Are Reused
1. Measure the dimensions of the cylinder block main bearing housing inner diameter and crankshaft main
journal diameter individually. Refer to
2. Apply the measured dimension to the “Main Bearing Selection Table”.
3. Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
4. Apply the symbol obtained to the “Main Bearing Grade Table” to select main bearing.
Bearing undersize table:
Refer to
EM-124, "Connecting Rod Bearing"
PBIC3263J
(A) : Basic stamp mark
: Engine front
PBIC3760E
(A) : Main journal diameter grade (No. 1 to 5 from left)
(B) : Crankshaft pin journal diameter grade (No. 1 to 4 from left)
PBIC3757E
HOW TO SELECT PISTON AND BEARING
EM-113
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Main Bearing Selection Table
Main Bearing Grade Table
Use Undersize Bearing Usage Guide
• When the specified main bearing oil clearance is not obtained with standard size main bearings, use under-
size (US) bearing.
• When using undersize (US) bearing, measure the main bearing inner diameter with bearing installed, and
grind main journal so that the main bearing oil clearance satisfies the standard.
CAUTION:
PBIC3759E
Main Bearing Grade Table
: Refer to
EM-114
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
HOW TO SELECT PISTON AND BEARING
In grinding crankshaft main journal to use undersize bearings,
keep fillet (A) [0.8 - 1.2 mm (0.031 - 0.047 in)].
Bearing undersize table:
Refer to
PBIC3263J
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-115
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009444759
GENERAL SPECIFICATIONS
Valve Timing
Unit: degree
( ): Valve timing control “ON”
Drive Belt
INFOID:0000000009444760
DRIVE BELT
Belt Deflection
*: When engine is cold.
Engine type
HR16DE
Cylinder arrangement
In-line 4
Displacement
cm
3
(cu in)
1,598 (97.51)
Bore and stroke
mm (in)
78.0
× 83.6 (3.071 ×3.291)
Valve arrangement
DOHC
Firing order
1-3-4-2
Number of piston rings
Compression
2
Oil
1
Compression ratio
9.8:1
Compression pressure
kPa (kg/cm
2
, psi) / 200 rpm
Standard
1,510 (15.4, 219)
Minimum
1,270 (12.95, 184)
Differential limit between cylinders
100 (1.0, 14.5)
Valve timing
: Intake valve
: Exhaust valve
a
b
c
d
e
f
216
228
11 (
−27)
ATDC
59 (-21)
ABDC
-1 (49)
ATDC
37 (-13)
BBDC
JPBIA4228ZZ
Location
Deflection adjustment *
Unit: mm (in)
Used belt
New belt
Limit
After adjusted
Drive belt
With A/C
10.0 (0.39)
4.9 - 5.2 (0.19 - 0.20)
4.1 - 4.4 (0.16 - 0.17)
Without A/C
9.1 (0.36)
4.3 - 4.7 (0.17 - 0.19)
3.7 - 3.9 (0.146 - 0.154)
Applied pushing force
98.1 N (10.0 kg-f, 22.0 lb-f)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст