Nissan Versa Note. Instruction — part 427
EXL-92
< SYMPTOM DIAGNOSIS >
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000009694080
The parking, license plate and tail lamps do not turn ON in any combination switch (lighting and turn signal
switch) position.
Diagnosis Procedure
INFOID:0000000009694081
1.
COMBINATION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) INSPECTION
Check the combination switch (lighting and turn signal switch). Refer to
.
Is the combination switch (lighting and turn signal switch) normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select TAIL & CLR REQ of IPDM E/R DATA MONITOR item.
2. While operating the combination switch (lighting and turn signal switch), check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(without Intelligent Key).
3.
PARK LAMP CIRCUIT INSPECTION
Check the parking lamp circuit. Refer to
EXL-11, "PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM :
.
Is the tail lamp circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Combination switch (lighting and turn signal switch)
1st
ON
OFF
OFF
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-93
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000009694082
The front fog lamps do not turn ON in any setting.
Diagnosis Procedure
INFOID:0000000009694083
1.
COMBINATION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) INSPECTION
Check the combination switch (lighting and turn signal switch). Refer to
.
Is the combination switch (lighting and turn signal switch) normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select FR FOG REQ of IPDM E/R DATA MONITOR item.
2. With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
3.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
.
Is the front fog lamp circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(Lighting switch 2ND)
ON
ON
OFF
OFF
EXL-94
< PERIODIC MAINTENANCE >
HEADLAMP AIMING ADJUSTMENT
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Inspection
INFOID:0000000008969395
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following:
• Ensure all tires are inflated to correct pressure.
• Place vehicle and screen on level surface.
• Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
• Coolant and engine oil filled to correct level, and fuel tank full.
• Remove cargo and/or luggage to maintain an unloaded vehicle condition.
• Confirm spare tire, jack and tools are properly stowed.
• Carefully wipe off any dirt from headlamp lens.
CAUTION:
Do not use organic solvent (thinner, gasoline etc.)
• Place a driver or equivalent weight of 68.5 kg (150 lb) on the driver seat.
• By hand, bounce the front and rear of the vehicle to settle the suspension and eliminate any static load.
• Place the front tires in the straight ahead position.
• Confirm headlamp aiming switch is set to "0" (zero) position.
• Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
NOTE:
• For headlamp aiming details, refer to regulations in your area.
• By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
• Use adjusting screw to perform aiming adjustment.
• Perform headlamp aiming if:
- The vehicle front body has been repaired.
- The front combination lamp has been removed or replaced.
- Any outfitting has been installed.
- The vehicle’s standard load condition has been substantially increased.
AIMING ADJUSTMENT SCREW
AIMING ADJUSTMENT SCREW
AWLIA2171ZZ
A.
Headlamp (LH) (UP/DOWN)
adjustment screw
B.
Headlamp (RH) (UP/DOWN)
adjustment screw
HEADLAMP AIMING ADJUSTMENT
EXL-95
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Aiming Adjustment Procedure
INFOID:0000000008969396
1. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
AWLIA2170ZZ
1.
Front combination lamp
A. Suitable tool (for aiming adjustment) B. Adjusting screw
A.
: 150 mm (5.91 in)
B.
: 100 mm (3.94 in)
C.
: 100 mm (3.94 in)
JSLIA0028ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст