Nissan Versa Note. Instruction — part 762
STEERING GEAR AND LINKAGE
ST-17
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2. Install large end (1) of boot (2) to gear housing assembly.
3. Install small end (3) of boot (2) to inner socket boot mounting
groove.
4. Install outer boot clamp to boot small end using suitable tool.
5. Install inner boot clamp to boot large end using suitable tool.
CAUTION:
Do not reuse boot clamps.
6. Install outer socket.
7. Adjust inner socket to standard length (L) and then tighten lock
nut to the specified torque. Check length of inner socket (L)
again after tightening lock nut.
CAUTION:
The length achieved after toe-in adjustment is not neces-
sarily the above value.
8. Check wheel alignment. Refer to
CAUTION:
AWGIA0107ZZ
AST139
Inner socket length (L)
: Refer to
SGIA0167E
ST-18
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
When tightening outer socket lock nut (1), be sure to hold
outer socket (2) using a suitable tool to prevent ball joint
from contacting knuckle.
Inspection
INFOID:0000000009385545
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks and replace it if damage exists.
Steering gear
• Check steering gear for damage and scratches to the inner wall. Replace if there are any abnormal condi-
tions.
Outer Socket and Inner Socket
Check the following items and replace the component if outside specification:
BALL JOINT SWINGING FORCE
• Hook a Tool at the point shown and pull the spring balance. Make
sure that the Tool reads the specified value when ball stud and
inner socket start to move. Replace outer socket (1) and inner
socket (2) if they are outside the standard.
BALL JOINT AXIAL END PLAY
• Apply an axial load of 490 N (50 kg-f, 110 lb-f) to ball stud. Using a
dial gauge, measure amount of stud movement and make sure
that the value is within the following specified range. Replace outer
socket (1) and inner socket (2) if the measured value is outside the
standard.
JSGIA0538ZZ
Tool number :
—
(J-44372)
Measuring point of outer
socket (1)
: Ball stud upper side (A)
Measuring point of inner
socket (2)
: Point (B)
Swinging force : Refer to
Axial end play : Refer to
JPGIA0188ZZ
JSGIA0109ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
ST-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000009385546
Steering Wheel Axial End Play and Play
INFOID:0000000009385547
Unit: mm (in)
Steering Wheel Turning Force
INFOID:0000000009385548
Unit: N (kg-f, lb-f)
Steering Angle
INFOID:0000000009385549
Unit: Degree minute (Decimal degree)
Steering Column Operating Range
INFOID:0000000009385550
*: For measuring position, refer to
Steering gear model
R24K
Item
Standard
Steering wheel axial end play
0 (0)
Steering wheel play on the outer circumference
0 - 35 (0 - 1.38)
Item
Standard
Steering wheel turning force
36 (3.7, 8.09) or less
Item
Standard
Inner wheel (Angle A)
Minimum
34
° 30′ (34.5°)
Nominal
37
° 30′ (37.5°)
Maximum
38
° 30′ (38.5°)
Outer wheel (Angle B)
Nominal
32
° 00′ (32.0°)
SGIA0055E
Item
Standard
Tilt operating range
*
39.4 mm (1.551 in)
Rotating torque
1.4 – 2.1 N·m (0.14 – 0.21 kg-m, 12 – 19 in-lb)
Steering column length
*
477.9 mm (18.81 in)
ST-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Rack Stroke
INFOID:0000000009385551
Unit: mm (in)
Ball Joint Swing Force
INFOID:0000000009385552
*: For measuring position, refer to
Ball Joint Axial End Play
INFOID:0000000009385553
Unit: mm (in)
Inner Socket Length
INFOID:0000000009385554
Unit: mm (in)
Item
Standard
Rack stroke neutral position (L)
64.6 (2.543)
JSGIA0272ZZ
Item
Standard
Outer socket
Spring balance measurement
*
6.0 – 58 N (0.61 – 5.9 kg-f, 1.35 – 13.03 lb-f)
Inner socket
Spring balance measurement
*
3.5 – 34.7 N (0.36 – 3.5 kg-f, 0.79 – 7.8 lb-f)
Item
Standard
Outer socket
0.5 (0.020) or less
Inner socket
0.2 (0.008 in) or less
Item
Standard
Inner socket length (L)
67.4 (2.654)
SGIA0167E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст