Nissan Versa Note. Instruction — part 869
WHEEL AND TIRE
WT-45
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
WHEEL AND TIRE
Exploded View
INFOID:0000000009446780
Removal and Installation
INFOID:0000000009446781
REMOVAL
1. Remove wheel nuts using power tool.
2. Remove wheel and tire.
INSTALLATION
Installation is in the reverse order of removal.
1.
Wheel and tire
JSGIA0969GB
WT-46
< REMOVAL AND INSTALLATION >
TRANSMITTER
TRANSMITTER
Exploded View
INFOID:0000000009443195
Removal and Installation
INFOID:0000000009443196
REMOVAL
1. Remove wheel and tire using power tool.
2. Remove valve cap and valve core to deflate the tire.
NOTE:
If the tire is to be reused, apply a matching mark on the tire in line with the position of the valve stem
assembly for the purpose of wheel and tire balance adjustment after installation.
3. Remove the valve stem nut and allow transmitter to fall into tire.
4. Lubricate the tire outside bead well with a suitable non-silicone lubricant, and remove outside of tire from
the wheel. Reach inside the tire and remove the transmitter.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the wheel and tire.
• Be sure not to damage the wheel or transmitter.
• Do not allow lubricant to make contact with transmitter.
5. Lubricate the tire inside bead well with a suitable non-silicone lubricant, and remove inside of tire from the
wheel.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
1.
Transmitter (tire pressure sensor)
2.
O-ring
3.
Valve stem nut
4.
Valve core
5.
Valve cap
6.
Valve stem assembly
:
Parts that are replaced as a set when the tire is replaced.
AWEIA0212GB
SEIA0047E
TRANSMITTER
WT-47
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• Be sure not to damage the wheel.
6. Remove the valve stem from the transmitter as shown.
INSTALLATION
1. Apply a suitable non-silicone lubricant to the tire inside bead.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
• Do not drop or strike the transmitter. Replace the transmitter if it has sustained an impact.
2. Install the tire inside bead (1) onto the wheel (2) in the position
shown.
3. Install the valve stem to the transmitter.
4. Install the O-ring to the transmitter.
CAUTION:
• Do not reuse O-ring.
• Insert O-ring to the base of the transmitter.
• The base of the valve stem (A) must be positioned in the
groove of the metal plate as shown.
JSEIA0378ZZ
JPEIC0105ZZ
JSEIA0376GB
WT-48
< REMOVAL AND INSTALLATION >
TRANSMITTER
5. Hold the tire pressure sensor as shown, and press the sensor in the direction (
) as shown to bring it into
absolute contact with wheel. After this, tighten valve stem nut to the specified torque.
CAUTION:
• Check that O-ring contacts horizontally with wheel.
• Check that the base of the valve stem is positioned in the groove of the metal plate.
• Be sure that no burrs exist in the valve stem hole of the wheel.
6. Install and tighten the valve stem nut to the specified torque.
CAUTION:
Do not use power tool for installation.
7. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
8. Apply a suitable non-silicone lubricant to the tire outside bead.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
• Do not allow lubricant to make contact with transmitter.
9. Install the tire outside bead onto the wheel as normal.
NOTE:
If the tire is being reused, align the matching mark applied on
the tire with the position of the valve stem assembly for the purpose of wheel and tire balance adjustment
after installation. Make sure that the tire does not rotate relative to wheel.
10. Install the valve core and inflate tire.
CAUTION:
Do not reuse valve core.
11. Install the valve cap.
CAUTION:
Do not reuse valve cap.
12. Balance the wheel and tire. Refer to
13. Install wheel and tire in the appropriate position on vehicle. Refer to
WT-45, "Removal and Installation"
NOTE:
If replacing the transmitter, then transmitter wake up operation must be performed. Refer to
.
14. Adjust neutral position of steering angle sensor. Refer to
.
JSEIA0465GB
Valve stem nut
tightening torque
WEIA0046E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст