Nissan Versa Note. Instruction — part 710
B210E STARTER RELAY
SEC-119
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO (WITH CVT)>>GO TO 4.
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.
2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
IPDM E/R
Clutch interlock switch
Continuity
Connector
Terminal
Connector
Terminal
E44
13
E34
2
Yes
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
SEC-120
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009705932
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Shift selector lever to the N position and wait 1 second or more.
4. Shift selector lever to the position other than P and N, and wait 1 second or more.
5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-120, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705933
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF BCM
Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect transmission range switch connector.
4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5. Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
IPDM E/R detects a difference between the
following signals
• P/N position signal from transmission
range switch and P/N position signal
(CAN) from BCM
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-121
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
F42
40
Ground
No
SEC-122
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009705934
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Shift selector lever to the N position and wait 1 second or more.
4. Shift selector lever to the position other than P and N, and wait 1 second or more.
5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-122, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705935
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF BCM
Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect transmission range switch connector.
4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5. Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW OFF
IPDM E/R detects a difference between the
following signals
• P/N position signal from transmission
range switch and P/N position signal
(CAN) from BCM
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст