Nissan Versa Note. Instruction — part 290
EC-142
< BASIC INSPECTION >
[HR16DE]
HOW TO SET SRT CODE
WITH CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode of “ENGINE” using CONSULT.
WITHOUT CONSULT
Perform “SRT status” mode with
EC-57, "On Board Diagnosis Function"
WITH GST
Select Service $01 with GST.
Is SRT(s) set?
YES
>> GO TO 12.
NO
>> Call TECH LINE or take appropriate action.
12.
CHECK PERMANENT DTC
NOTE:
Permanent DTC cannot be checked with a tool other than CONSULT or GST.
WITH CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode of “ENGINE” using CONSULT.
WITH GST
Select Service $01 with GST.
Is permanent DTC(s) detected?
YES
>> Proceed to
.
NO
>> END
HOW TO ERASE PERMANENT DTC
EC-143
< BASIC INSPECTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
HOW TO ERASE PERMANENT DTC
Description
INFOID:0000000009020665
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same mal-
function is not detected after performing the driving pattern for MIL shutoff three times in a raw.
When a DTC is not stored in ECM
The erasing method depends on a permanent DTC stored in ECM. Refer to the following table.
NOTE:
If the applicable permanent DTC includes multiple groups, perform the procedure of Group B first. If the per-
manent DTC is not erased, perform the procedure of Group A.
×: Applicable —: Not applicable
*: For group, refer to
PERMANENT DTC ITEM
For permanent DTC items, MIL turns ON. Refer to
*1: When the same malfunction is de-
tected in two consecutive trips, MIL
will illuminate.
*2: MIL will turn off after vehicle is driven
3 times (driving pattern B) without
any malfunctions.
JSBIA0063GB
Group
*
Perform “DTC CONFIRMATION PROCEDURE” for
applicable DTCs.
Driving pattern
Reference
B
D
A
×
—
—
B
—
×
×
EC-144
< BASIC INSPECTION >
[HR16DE]
HOW TO ERASE PERMANENT DTC
PERMANENT DTC SERVICE PROCEDURE
Work Procedure (Group A)
INFOID:0000000009020666
JSBIA0401GB
JSBIA0064GB
HOW TO ERASE PERMANENT DTC
EC-145
< BASIC INSPECTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
CHECK DTC
Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
EC-57, "On Board Diagnosis Function"
NO
>> GO TO 2.
2.
CHECK PERMANENT DTC
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES
>> GO TO 3.
NO
>> END
3.
PERFORM DTC CONFIRMATION PROCEDURE
Perform “DTC CONFIRMATION PROCEDURE” for DTCs which are the same as permanent DTCs stored in
ECM. Refer to
>> GO TO 4.
4.
CHECK PERMANENT DTC
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES
>> GO TO 1.
NO
>> END
*1: When the same malfunction is de-
tected in two consecutive trips, MIL
will illuminate.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст