Nissan Versa Note. Instruction — part 237
KEY CYLINDER SWITCH
DLK-233
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1. Disconnect BCM connector M18.
2. Check continuity between front door lock key cylinder switch LH connector and BCM connector M18.
3. Check continuity between front door lock key cylinder switch LH connector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
DLK-233, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace front door lock key cylinder switch LH. Refer to
DLK-288, "DOOR LOCK : Removal and
Component Inspection
INFOID:0000000009645384
COMPONENT INSPECTION
1.
CHECK DOOR KEY CYLINDER SWITCH
Check front door lock key cylinder switch LH.
Is the inspection result normal?
YES
>> Key cylinder switch is OK.
NO
>> Replace front door lock key cylinder switch LH. Refer to
DLK-288, "DOOR LOCK : Removal and
Front door lock key cylin-
der switch LH connector
Terminal
BCM connector
Terminal
Continuity
D14
6
M18
8
Yes
5
7
Front door lock key cylin-
der switch LH connector
Terminal
Ground
Continuity
D14
6
No
5
Terminal
Key position
Continuity
Front door lock key cylinder
switch LH connector
6
4
Lock
Yes
Neutral / Unlock
No
5
Unlock
Yes
Neutral / Lock
No
DLK-234
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEY SWITCH (BCM INPUT)
KEY SWITCH (BCM INPUT)
Diagnosis Procedure
INFOID:0000000009645385
Regarding Wiring Diagram information, refer to
.
1.
CHECK KEY SWITCH INPUT SIGNAL
With CONSULT
Check key switch "KEY ON SW" in DATA MONITOR mode with CONSULT. Refer to
: CONSULT Function (BCM - DOOR LOCK)"
• When key is inserted to ignition key cylinder:
• When key is removed from ignition key cylinder:
Without CONSULT
Check voltage between BCM connector M18 terminal 37 and ground.
Is the inspection result normal?
YES
>> Key switch (insert) circuit is OK.
NO
>> GO TO 2
2.
CHECK KEY SWITCH (INSERT)
1. Turn ignition switch OFF.
2. Disconnect key switch connector.
3. Check continuity between key switch terminals.
Is the inspection result normal?
YES
>> Repair or replace harness or fuse.
NO
>> Replace key switch.
KEY ON SW
: ON
KEY ON SW
: OFF
Connector
Terminal
Condition
Voltage (V)
(+)
(–)
M18
37
Ground
Key is inserted.
Battery voltage
Key is removed.
0
Terminals
Condition
Continuity
1 – 2
Key is inserted.
Yes
Key is removed.
No
DOOR LOCK ACTUATOR
DLK-235
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009645386
Locks/unlocks the door with the signal from BCM.
DRIVER SIDE : Component Function Check
INFOID:0000000009645387
1.
CHECK FUNCTION
1. Use CONSULT to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-235, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009645388
Regarding Wiring Diagram information, refer to
.
1.
CHECK OUTPUT SIGNAL
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> GO TO 2
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and front door lock actuator driver side connector.
3. Check continuity between BCM connector and front door lock actuator driver side connector.
4. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock actuator LH. Refer to
DLK-288, "DOOR LOCK : Removal and Installa-
.
Terminals
Condition of
door lock and
unlock switch
Voltage (V)
(Approx.)
(+)
(–)
BCM
connector
Terminal
M19
41
Ground
Unlock
0
→ Battery voltage → 0
54
Lock
0
→ Battery voltage → 0
BCM connector
Terminal
Door lock actuator
connector
Terminal
Continuity
M19
41
D14
2
Yes
54
1
BCM connector
Terminal
Continuity
M19
41
Ground
No
54
DLK-236
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000009645389
Locks/unlocks the door with the signal from BCM.
PASSENGER SIDE : Component Function Check
INFOID:0000000009645390
1.
CHECK FUNCTION
1. Use CONSULT to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-236, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009645391
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> GO TO 2
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM and front door lock actuator RH connectors.
2. Check continuity between BCM connector and front door lock actuator RH.
3. Check continuity between BCM connector and ground.
Terminals
Condition of
door lock and
unlock switch
Voltage (V)
(Approx.)
(+)
(–)
BCM
connector
Terminal
M19
54
Ground
Lock
0
→ Battery voltage → 0
53
Unlock
0
→ Battery voltage → 0
BCM connec-
tor
Terminal
Front door lock
actuator RH
connector
Terminal
Continuity
M19
54
D114
2
Yes
53
1
BCM connector
Terminal
Continuity
M19
54
Ground
No
53
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст