Nissan Versa Note. Instruction — part 729
DRIVER AIR BAG MODULE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2. Locate the access holes on side of steering wheel rear finisher
(1) and insert (
) a 5.0 mm (0.20 in) diameter suitable tool (A).
3. Push suitable tool inward (
) and make sure the tool contacts
the spring (D). While pushing on spring (D), push on the driver
air bag module. The driver air bag module hook will release,
then pull to release from steering wheel. Repeat procedure on
springs (B) and (C).
NOTE:
Driver air bag module removed for clarity.
4. Lift driver air bag module away from the steering wheel and dis-
connect the driver air bag module harness connectors (A) and
the horn harness connector (B). Then remove the harnesses
from hook (C).
NOTE:
Take note of harness routing for correct installation.
CAUTION:
• For removing/installing the driver air bag module harness
connector, insert a thin screwdriver wrapped in tape into
the notch, then lift the lock and remove the harness con-
nector as shown.
• Install the harness connector with the lock raised, and
push the lock into the connector as shown.
• After installing the connector, check that the lock is
pushed in securely.
AWHIA0528ZZ
AWHIA0551ZZ
PHIA0953J
SR-14
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
5. Remove the driver air bag module.
CAUTION:
• Always place the driver air bag module with pad side fac-
ing upward.
: Upward
• Replace the driver air bag module if it has been dropped
or sustained an impact.
• Do not strike the driver air bag module.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
To install the driver air bag module onto the steering wheel, align the hooks over the springs and push to snap
into place.
CAUTION:
• Always route driver air bag module harness in original location.
• Be careful not to damage or pinch the harness while installing.
• After the work is completed, check the function of the horn and each steering switch.
• After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
JMHIA2077ZZ
JMHIA0009ZZ
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000008969284
Removal and Installation
INFOID:0000000008969285
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not disassemble the spiral cable.
• Do not use air tools or electric tools for servicing.
CAUTION:
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove steering wheel. Refer to
ST-8, "Removal and Installation"
3. Remove steering column covers. Refer to
IP-17, "Removal and Installation"
.
4. Disconnect the harness connector (A) from spiral cable and har-
ness connector (B) from steering angle sensor.
1.
Combination switch
2.
Steering angle sensor
3.
Spiral cable
Pawl
AWHIA0504ZZ
ALHIA0272ZZ
SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
5. Remove screws (A), then release pawls and remove spiral cable
and steering angle sensor (1) as an assembly.
: Pawl
CAUTION:
Do not turn the spiral cable quickly or beyond the limit
number of turns (approximately 2.5 turns from the neutral
position), this may cause the cable to snap.
6. Remove screws (A), then release pawls (B) and separate the
steering angle sensor (2) from spiral cable (1).
CAUTION:
Do not reuse steering angle sensor.
CAUTION:
• Do not strike or drop the spiral cable.
• Replace the spiral cable if it has been dropped or sustained
an impact.
INSTALLATION
Installation is in the reverse order of removal.
• The turn signal lever must be in the neutral position for spiral cable installation.
AWHIA0538ZZ
ALHIA0271ZZ
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст