Nissan Versa Note. Instruction — part 658
PREPARATION
RAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009486646
The actual shapes of Kent-Moore tools may differ from those of special tools illustrated here.
Commercial Service Tool
INFOID:0000000009486647
Tool number
(Kent-Moore No.)
Tool name
Description
ST30720000
(
—
)
Drift
Installing hub cap
a: 77 mm (3.03 in) dia.
b: 55 mm (2.17 in) dia.
KV40104730
(
—
)
Drift
Installing wheel bearing
a: 53.7 mm (2.114 in) dia.
b: 47 mm (1.85 in) dia.
c: 15 mm (0.59 in).
ST33710000
(
—
)
Drift
Removing wheel bearing
a: 30 mm (1.18 in) dia.
b: 23 mm (0.91 in) dia.
ST30032000
(
—
)
Drift
Installing sensor rotor
a: 38 mm (1.50 in) dia.
b: 80 mm (3.15 in) dia.
ZZA0701D
ZZA1133D
ZZA1234D
ZZA0881D
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
RAX-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009486648
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
—
Possible cause and SUSPECTED PARTS
Im
pro
pe
r in
st
a
lla
tion
, lo
os
en
es
s
Part
s int
erference
Whe
e
l be
ari
ng da
ma
ge
REAR AXLE AND
R
E
AR SUSPENSI
ON
TIRE
ROAD WHEEL
BRAKE
Symptom
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
REAR WHEEL HUB
RAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB
Inspection
INFOID:0000000009486649
• Check the axle and suspension parts for excessive play, wear, or damage.
• Shake each rear wheel to check for excessive play as shown.
REAR WHEEL BEARING INSPECTION
• Move wheel in the axial direction by hand. Make sure the axial end play is within specification.
• Check that the wheel bearing operates smoothly.
• Replace the wheel bearing if the axial end play exceeds specification, or if the wheel bearing does not turn
smoothly. Refer to
RAX-6, "Removal and Installation"
.
CAUTION:
The wheel bearing does not require maintenance. If any of the following symptoms are noted,
replace the wheel bearing.
• Growling noise is emitted from the wheel bearing during operation.
• Wheel bearing drags or turns roughly.
SMA525A
Axial end play
: Refer to
RAX-6
< REMOVAL AND INSTALLATION >
REAR WHEEL HUB
REMOVAL AND INSTALLATION
REAR WHEEL HUB
Exploded View
INFOID:0000000009486650
Removal and Installation
INFOID:0000000009486651
REMOVAL
1. Remove the wheel and tire using power tool. Refer to
WT-45, "Removal and Installation"
.
2. Remove hub cap from brake drum using a suitable tool.
3. Remove wheel hub lock nut and brake drum.
CAUTION:
• Do not depress brake pedal while rear drum is removed.
• Do not apply force to the brake drum to avoid damage to the wheel bearing. If the wheel bearing
inner race is separated due to force, replace the wheel bearing with a new one.
4. Remove spindle bolts. Separate back plate and spindle from rear suspension beam.
CAUTION:
Do not remove rear brake components. Support the rear brake components using wire.
5. If required, remove the wheel studs from brake drum using a suitable press.
CAUTION:
• Do not hammer the wheel stud and avoid impact to the brake drum.
• Press the wheel stud straight out to avoid damage.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear suspension beam
2.
Rear brake components
3.
Spindle
4.
Sensor rotor
5.
Snap ring
6.
Wheel bearing
7.
Wheel stud
8.
Brake drum
9.
Wheel hub lock nut
10. Hub cap
AWDIA1107ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст